Gerber Crucial F.A.S.T.
-
Hey since lots of Gerbers are made in China (this one included I believe) why not use 8CR13MoV for blades? It's pretty much AUS 8 equivalent (which would actually be superior to Leatherman's 420HC for edge holding) and wouldn't cost much more, and it's already being made in the country these come from. Just a thought.....
-
@hawkchucker said:
OK this is coming from me... I AM GLAD THIS GERBER LOOKS LIKW A WINNER.Uggg I need a shower.
Don't you feel better now? :D :D
-
Well the problem with the China made products is simple. There is 2 Chinas. I know it sounds strange, but it is wierd how diff manufacturers can have diff results. Take Multitasker and the suspension. Two tools made in china but one is Fantastic anf the other rubbish. The Multitasker is a tank and very well built. Hopefully this is how they decided to go now. You can have some things made well overthere, but you need to as a manufacturer specify that is what you want.
-
You are preaching fancy steels to a guy that doesn't believe in the steel race. I understand that some steels have better performance than others, but I'm happy if it takes a decent edge, cuts what I need to cut and is easily touched up. Beyond that, labels be damned.
Def
-
Well steels do make a difference in stuff, but not in my multis. I am actually happy having them with 420 or lesser like aus6. Multis arnt the do everything they are the thing you use because you are away from your rollaway. I carry premium steels in my knives. so I can live with the lesser steels in multis.
-
Oh I don't need super steel, just something decent, I always thought old Leatherman 420HC was fine and hoping Gerber is at least in that ballpark. On pocket clip tools intended to kinda fill in for EDC knives though it might not be bad for Gerber to upgrade like Leatherman did with the CX stuff. I'm not saying even 154CM mind you, but just something they could advertise like the 8Cr13 stuff or maybe AUS 8 or just something the knife buying public would recognize as a steel they have seen in say a Kershaw or a Byrd or Spyderco or what have you. Don't have to be fancy, just something on par with lots of $20-$30 EDC folders out there that let you know what steel they are using. Heck the Sandvik steels are cheap and easy to blank but really very good and fine grained, 13C26 for example. I do lots of cardboard and tape cutting in my job, so I'll test out the Crucial and report back when I get a chance.
-
Just a bump. Anyone gotten one of these yet?
-
I think Marlinaholic has one.
-
Ebay = $42.98 shipped
<u>I just ordered one</u>, hoping it doesn't get loose like my green original did.......Is there a way to tighten then? I have tried everything and the funky screws wont budge, ( even heated it with a torch to loosen the lock-tight...if any? ) I was hoping to tighten it or shim it.
-
@dangerousatom said:
Ebay = $42.98 shipped<u>I just ordered one</u>, hoping it doesn't get loose like my green original did.......Is there a way to tighten then? I have tried everything and the funky screws wont budge, ( even heated it with a torch to loosen the lock-tight...if any? ) I was hoping to tighten it or shim it.
Howdy Dangerous

You sayin' the knife blade on yours loosened up?
-
@J-sews said:
[quote author=dangerousatom link=topic=25401.msg468081#msg468081 date=1298322288]Howdy Dangerous

You sayin' the knife blade on yours loosened up?
The blade being loose would be an understatement....I can pitch the blade back and forth about 3/8". It only had maybe 6-months of light use on it too.
-
Sounds like pivot has loosened up (no thread lock perhaps?) will it tighten down, or is it something else?
BTW welcome to the forum.

-
-
The details haven't been worked out just yet (as far as I know) so send Travis a PM for now so he knows you want in.
Def
-
@Gareth said:
Sounds like pivot has loosened up (no thread lock perhaps?) will it tighten down, or is it something else?BTW welcome to the forum.

I assume the pivot you speak of is the axis pin that the blade and driver bits turn on?? If so then yes. I just took another look at it today and I can squeeze the exterior green plates closer together with my fingers, so Im still assuming its the screw that holds the one end together.....? No I cant tighten it or loosen it, its nearly impossible to get a bite on the screws that hold it down. I did use the correct torques driver, but it spun the teeth off the screw due to it not wanting to turn
.....Im about ready to drill the head off and put a stainless allen with a blind nut on the other side<u>Wish i knew about the group buy.....Id have waited a bit to save a few bucks</u>
-
From this point on, for yours and everyone else's benefit, whenever a new tool is coming on the merket, contact Travis Autry for details on a potential group buy. It is one of the projects we have planned for the Multitool.org Store.
Def
-
Sounds like pivot has loosened up (no thread lock perhaps?) will it tighten down, or is it something else?
BTW welcome to the forum.
http://twitter.com/EDCSourceI assume the pivot you speak of is the axis pin that the blade and driver bits turn on?? If so then yes. I just took another look at it today and I can squeeze the exterior green plates closer together with my fingers, so Im still assuming its the screw that holds the one end together.....? No I cant tighten it or loosen it, its nearly impossible to get a bite on the screws that hold it down. I did use the correct torques driver, but it spun the teeth off the screw due to it not wanting to turn
.....Im about ready to drill the head off and put a stainless allen with a blind nut on the other side<u>Wish i knew about the group buy.....Id have waited a bit to save a few bucks</u>
Yeah that's what I'm talking about. If it were me I'd leave it alone and send it in under your warrenty, Gerber have a pretty good reputation for getting these things sorted.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login