Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Leatherman design flaw or engineering success?

Scheduled Pinned Locked Moved Leatherman Tools
9 Posts 1 Posters 7.2k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Leatherman design flaw or engineering success?
Leatherman design flaw or engineering success?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Jors Offline
    Jors
    Posts: 298
    Jors Offline
    Jors
    wrote on last edited by Jors
    Quote Reply

      Leatherman design flaw or engineering success?

      I have recently read an old article about someone that has a problem with the Core. The pliers jaws embeds itself between some of the tools when he closes the tool.

      I have inspected my few Leathermans and took some photographs to state my point. I invite members with other models to post pics here and state their problems or successes here.

      The Supertool 300:


      In the centre pic you can see the cams that poses friction when it goes underneath the edge on the right of it when you open the pliers. It stops against tat edge as shown in the bottom pic.


      There are no stopping plates/pins inside the handles. The pliers jaws slide against the Phillips and medium flat screw drivers. The tools sizes are perfectly designed and of the correct sizes.


      You can see on the pics how the jaws slide against the tools which forces the pliers jaws closed.

      The Supertool 300 has not even once imposed any problems with wedging.

      The Leatherman Surge:


      The cams wedges exactly the same as with the Supertool 300. On the right hand side you can see the stopping flat inside the handle, against which the pliers jaws slides to prevent it from wedging between the tools.


      On the left the jaw tips wedges between the awl and big screw driver. It bites against the latter. On the right the jaw tip have touched the screw driver bit. It has bitten a tiny groove in it’s shoulder.
      This happen when you close the tool in one step and is more relevant when the tool is still new and the force to overcome the gripping power of the cams is bigger than the stopping flats’ ability to withstand bending.


      Here is how to close the Surge in two steps. The top left picture shows how both hands must be held (as the left one – my right hand held the camera, therefore the thump is just to prevent the tool turning to the right as the left side has already disengaged the cams.
      The bottom left is the second position before any of your hand may be released. Your upper forefingers prevent the pliers from going inside the handles until in this position.
      Now you can close the tool. The tip of the jaws do not touch the stopping flat but the part of the jaws further back and the tips perfectly clear the tool without failing.

      Although the Surge is still my top tool and my EDC I feel Leatherman could reinforced the stopping flat. Th flat can not be raised higher, because then the tool can not be closed fully. The tolerances are very little.

      The Leatherman Pulse:


      No stopping flats and no wedging. Similar designe of the Supertool 300.
      No problems.

      Leatherman Wave:

      The Charge models should be similar, but I don’t know for sure.


      The cams are similar than the Surge.
      The stopping pins are very sturdy and strong.


      There are no wedging problems detected and the tool can be closed in a single movement.

      The Leatherman MUT (STD):


      The cams are the same as the ST300 as the both have the same new head.


      In the short handle there in no stopping flat/pin but only an edge. New design.


      In the long handle there is no pin/flat either, but a ridge.

      The MUT is a new design, well thought through and no wedging could be detected. Well done Leatherman.

      Please post pics of the other Leatherman tool and comment on wedging problems or the smoothness of closing. The more I study the Leatherman tools the more I feel they are the best.

      1 Reply Last reply
      • Grant Lamontagne Offline
        Grant Lamontagne
        administrators
        Posts: 67,980
        Grant Lamontagne Offline
        Grant Lamontagne
        administrators
        wrote on last edited by
        #1 Quote Reply

          This takes us back to the early days of Multitool.org when (I believe) a member named Colubrid had issues with a brand new Core getting all scratched up when the plier head would wedge in beside the screwdriver. He tried several new Cores in store and all had the same flaw, and he eventually complained to Leatherman who offered to look at his tool. In an effort to fix it they moved some of the internal components around, but I don't believe it was ever done to Colubrid's satisfaction.

          Good to see it revisited...

          Def


          1 Reply Last reply
          • J-sews Offline
            J-sews
            Admin Team
            Posts: 23,224
            J-sews Offline
            J-sews
            Admin Team
            wrote on last edited by
            #2 Quote Reply

              @Jors said:
              Leatherman Wave:

              The Charge models should be similar, but I don’t know for sure.


              The cams are similar than the Surge.
              The stopping pins are very sturdy and strong.

              To be precise, the stopping pins are sturdy and strong <u>now</u>. When the New Wave and the Charge models first came out in 2004, the stop pins were weak and prone to breakage. According to member Kwakster, who worked at an authorized Leatherman repair center, broken stop pins were one of the most frequent problems he encountered. In response to this, Leatherman re-designed the stop pins in 2008, making them much stronger.

              You can see the difference in this photo. On top is the old style stop, date code 0807. Below is the new stop, date code 0808

              1 Reply Last reply
              • New_World Offline
                New_World
                Posts: 1,795
                New_World Offline
                New_World
                wrote on last edited by
                #3 Quote Reply

                  this thead has got me looking at my leatherman multitools closely.

                  to my dissatisfaction... I am picky like Colubrid.
                  but i really like my LM cores.

                  1 Reply Last reply
                  • sergemaster Offline
                    sergemaster
                    Posts: 1,058
                    sergemaster Offline
                    sergemaster
                    wrote on last edited by
                    #4 Quote Reply

                      Amici,
                      My Juice S2 has been doing this since I purchased it. I try to live with it although that slight grinding noise which occurs if I don't close it a certain way still irks me.

                      Cheers,
                      Serge

                      1 Reply Last reply
                      • Malarauko Offline
                        Malarauko
                        Posts: 203
                        Malarauko Offline
                        Malarauko
                        wrote on last edited by
                        #5 Quote Reply

                          Now this is really interesting. When I first got my ST300 this was like the second thing I checked for. I've never had any problems with any of my Leathermans doing this and they're all pretty new tools. I think this is something they've improved with time.

                          On another note if this did happen it would wind me up massively. None of my tools are really drawer queens but theres something really annoying about damage I didn't cause.

                          1 Reply Last reply
                          • New_World Offline
                            New_World
                            Posts: 1,795
                            New_World Offline
                            New_World
                            wrote on last edited by
                            #6 Quote Reply

                              i expect 100% perfection in my tools and I don't get it hardly ever.
                              there are always those very minor gripes. (or bigger gripes)

                              1 Reply Last reply
                              • Mercury Offline
                                Mercury
                                Admin Team
                                Posts: 8,922
                                Mercury Offline
                                Mercury
                                Admin Team
                                wrote on last edited by
                                #7 Quote Reply

                                  I don't get that on my pulse as long as all the tools are closed. If the medium flat blade is deployed, the pliers have nowhere to stow, and they slide under the rest and bind up. I wouldn't call it a design flaw as much as an unfortunate gap that must be watched. It only happens on the flat blade, not the phillips.

                                  1 Reply Last reply
                                  • Desmodromic Offline
                                    Desmodromic
                                    Posts: 118
                                    Desmodromic Offline
                                    Desmodromic
                                    wrote on last edited by
                                    #8 Quote Reply

                                      I have the same problems as discribed with a LM Charge. Got them second hand from my father after I gave him a surge for his BD.

                                      I heared there is a great warranty system so will get it fixed asap.

                                      1 Reply Last reply

                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                      With your input, this post could be even better 💗

                                      Register Login

                                      1. Home
                                      2. Tool Talk
                                      3. Leatherman Tools
                                      4. Leatherman design flaw or engineering success?
                                      Reply
                                      • Reply as topic
                                      Log in to reply
                                      COMMUNITY LINKS
                                      EDC-TV SAKWiki GearFeed SAKSelector
                                      Operational Funds

                                      Help us keep the Unworkable working!

                                      Make A Donation
                                      November Goal: $300.00
                                      Due Date: Nov 30
                                      Total Receipts: $0.00
                                      Below Goal: $300.00
                                      0% funded
                                      • Login

                                      • Don't have an account? Register

                                      • Login or register to search.
                                      • First post
                                        Last post
                                      0