Squirt ES4/PS4 Owner's Club
-
I got my first leatherman today. A blue PS4 with screws

Negative comments I had read before were
- pliers are to tight/hard to open
- screwdrivers are too hard to access
Here are my thoughts
Overall quality fairly good. Yes the screw drivers and most of the other tools are a little hard to access the nail slots. I can get them no worries so this is not an issue for me and i only cut my nails yesterday and like them really short. The blade is quite sharp, actually very sharp, a lot sharper than I was expecting. I can shave with it. Its only sharpened on one side so im not sure what the deal with that is.
Things I don’t like are the scissors are very floppy/loose at the center rivet. The lever you press on feels like its going to fall off the rivet, its that loose. Im disappointed in that and a bit scared to use them really as the hand lever seems like its just dangling there. No where near the same quality as Victorinox classic scissors. The scissors also seem to scrape/hit something when I try to fold them back into the handle. I think they are just a tight fit with not much clearance. It’s not a major issue for me though.
The second thing I was disappointed in was that the main rivet joint for the pliers is a bit loose and there is sideways movement in the 2 plier jaws. I was expecting not to have this in a ‘quality’ brand of pliers. Maybe its just mine or maybe they are all like that? At least the needle nose tips do line up though.
The last thing is that the pliers don’t close right up. There is a gap so it would only clamp and hold something 0.50-0.75mm. This might be normal or it may not be but I certainly wont be able to hold any real thin things.
I tried the wire cutters on some thin wire maybe about 0.50 thickness. I would be a bit worried about trying anything more than small paper clip thickness. The pliers just seem a bit weak/vulnerable mainly due to how thin they are so you could only use these for very light work like electronics I reckon. The cutters would be good for circuit board work.
Overall I would say the quality is not as good as Victorinox. I have some Gerbers coming next week so it will be interesting to see how it compares to those.
I dont expect the blue annodized finish to last but when it does rub off you could either polish the handles or bead blast them to make them look better. I like the spring action of the pliers.
I am pretty happy with the PS4 and the main things I don’t like are the sloppy/loose scissor pivot and the loose plier pivot.
Would I buy another one? Yes I would so I could compare it to another to see if I got a dud but I wont pay the high price I paid for this one. I would like to get a red and black one to go with my blue one.
-
Cyclone,
I own two PS4 and for comparison to yours and to themselves, I can say that:
Both have pliers that meet at the very tip (can hold normal printer paper..) and a gap starts to appear as the pliers move toward the pivot point.
Neither have pliers that are lose with side to side movement.
One has scissors that have side to side movement, while the other has scissors that has no side to side movement.
The scissors on both need to be pushed the whole way to get them to go back in (they do not snap shut like on a swiss army knife). As for the scraping/hitting - if you look down in to the handle you will see that there is a plastic liner that has a slope to it which is suppose to help guide the scissors as they close.
Edit: what I wonder about the scissors is if the spring bar will eventually break off. I have a wenger swiss army knife that has similar sized scissors but a lot more robust spring bar.
-
Neither have pliers that are lose with side to side movement.
One has scissors that have side to side movement, while the other has scissors that has no side to side movement
Damn looks like i got a dud then. They definietly have that dreaded wobble at the plier pivot. Scissors are horrible to be honest.
Not sure if i can or should do anything about it. It was from a business on ebay Australia. If it has to be sent back to LM usa that could take ages to sort out.
I will hope i got a dud and will still try another one and some other leathermans but if i keep finding more doggy Leathermanslike this with loose pliers i dont think i will get any more and will stick with Victorinox tools. There are plenty of cheap brands out there you can buy with faults like sloppy pliers. I have got 2 LM mini tools on the way so i hope they are alright and it just proves my squirt just wasnt quite right.
I assume these are hand built so why dont they feel these things when inspecting them? surely they would feel the rock in the pliers and be not happy to send that out? If they are loose brand new they are only going to get worse with use.
-
Certain features of certain models of LM may be hand assembled and inspected but much of their factory is completely automated and robotic. There's a video of it all I'm sure some multi tooler dude with a better memory than mine will be linking to shortly....
As for the play in the hinges I never even noticed any and have thought of my PS4s as being quite comparable to my half dozen or so other LM tools. Of course now that you point it out however I see there is a bit of play in the scissors but it is of little concern, they are sharp and cut through several pieces of paper with little effort or difficulty, and as for the scrape you encounter when returning them to the body, I have none. Being as small as they are they do seem a bit of an afterthought compared to my Micra, S4, or Style CS scissors but those are all primarily scissors based so it doesn't surprise me.
I only just now dug out my old SAKs (sorry I don't know their model numbers but we could figure it out if need be) which are the comparable length to the PS4 and both of their scissors, hardly ever used, both have noticeably more play to them.
My PS pliers have virtually zero play in the pliers hinge, will grip a single sheet of paper tightly [at least if the front tip is used as well], and a side examination by holding them up to the light of my computer screen as a rear illumination shows the gap between the upper and lower teeth to be very small. The only thing I have on hand skinny enough for them not to grip between the upper and lower teeth is a human hair.
The very tip of the pliers meet perfectly and will grip a human hair tightly, however, so in a sense they could double as tweezers.
-
Cyclone,
Another thing to consider is if they'll fix it or replace it if you send it back (replacements likely having rivets). Since it is a model with screws, maybe you can convince them to send you replacement pliers and scissors instead?
-
It does sound like you've got a duffer mate. :-\ I'd perhaps try the company you bought it from and see if they'll replace it and deal with sending it back to LM.
-
Good grief,I must be a club member!I bought a PS4 on a whim back in December.It currently recides in my Emergancy Tin :D


On another vaugly related note,I bought a Gerber Clutch this week(mostly as a result of Chakos excellent review of the Bear Grilis tool(s).The PS4 is IMO far better even though it is £20 or so more expensive.
I got my PS4 from Blacks(one of the OutDoorsy fashion shops in the UK) for a penny shy of £30
-
Kirk, would you mind giving a list of what all you keep in your tin? It looks neat.

-
@Sazabi said:
Kirk, would you mind giving a list of what all you keep in your tin? It looks neat.
No problem!
LM Squirt PS4
6x inbuprofen tabs
Whistle
lighter
Lenser torch(V2 as far as I can remember)
2xmini S-binders
Waterproof capsule holding £20
bunch of elastoplasts
2xsalt sachets
2xhand whippes
needle and thread
tube of superglue(missing as if got used today to repair a Harry Potter Phenoix)
2xelastic bandsIts got most of the stuff I reckon I'd need in London if a bit of Smurf hits the fan!
-
Thanks, Kirk; it looks well thoughtout. :) I don't know what I'm more jealous of: your little kit, or knowing you have a Phoenix. :D
-
-
Kirk, I'm intrigued by your tin's rubber gasket. Is she watertight and what sort of vessel is she?
-
it appears to be a BCB international combat survival tin
-
@Cleanser said:
it appears to be a BCB international combat survival tinAFAIK those are just what we think of as tobacco tins, like these: http://www.roll-ups.co.uk/ishop/879/shopscr341.html
-
@Gareth said:
AFAIK those are just what we think of as tobacco tins, like these: http://www.roll-ups.co.uk/ishop/879/shopscr341.htmlThe "Baldwin's Nervous Pills" are great.. :D :D
-
it appears to be a BCB international combat survival tin
AFAIK those are just what we think of as tobacco tins, like these: http://www.roll-ups.co.uk/ishop/879/shopscr341.html
Give the man a cocanut!
-
I've asked in a few smoke shops that actually sell raw tobacco if they sell empty tobacco tins and they look at me like I'm from Mars and that it is an absurd question. :-[ {I think ziplock bags are what they sell their product in these days, around here, at least}
Google searches of US companies usually turns up nothing but collectible antiques. Anyone here know of a source for new tobacco tins in the US?
Edit to add: There is a place called "Best Glide" which sell what looks to be a BCB Survival tin for 5 dollars but their shipping charge is $7 !
-
@mzil said:
I've asked in a few smoke shops that actually sell raw tobacco if they sell empty tobacco tins and they look at me like I'm from Mars and that it is an absurd question. :-[ {I think ziplock bags are what they sell their product in these days, around here, at least}Google searches of US companies usually turns up nothing but collectible antiques. Anyone here know of a source for new tobacco tins in the US?
Edit to add: There is a place called "Best Glide" which sell what looks to be a BCB Survival tin for 5 dollars but their shipping charge is $7 !
Dont know if this helps,but its the tin I bought for my little kit
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200535997941&ssPageName=STRK:MEWNX:IT -
Kirk, thanks. Looks good but all the sources I find are UK based. I guess I could evenentually find one that ships to the states but then, once again, the sipping greatly exceeds the unit's price. Oh well.
-
Sadly I remember when you could buy these tins of tobacco (Golden Virginia) from any corner shop. Not sure that's the case any more though. :-\
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login