SuperJuice KFS4
-
It's ok Bob, my sideclip polishing project barely left the ground before I put it on the back burner, and all I have to do is polish it then assemble it! You have to make stuff for your mod, I sympathize!
-
@J-sews said:
Then things were proceeding nicely again, until it became apparent that my pivot screws are too short. :'( The ones I bought from www.knifekits.com are one half inch long:
Unfortunately, it appears they need to be just a little bit longer. :( These are already the longest ones knifekits sells, so I'll have to make my own.
Just curiously, what diameter are the pivot pins?
I have a coupla semi-børked Juices, and have been considering a layer mod, and really REALLY didn't wanna have to deal with peening pins!
(Before anybody asks: Knife, Scissors+Bottle Opener, Saw (yes, saw)+Awl, File. No serrated knife, no freakin' corkscrew. Basically, a KF4 with scissors instead of the serrated blade.)
I'm betting they're prolly some 300-series stainless. Too bad you couldn't harden them...
The Juice pins are 5/32 (or .156") in diameter. Unfortunately though, they are just slightly too short to work on a tool of Kf4 thickness. :( You would have to drop one whole layer in order for these pins to work. >:(
What if you just made two of those pivot tubes into one, and fixed them togehter with a grub screw in the middle? Would that become loose too quickly? I can't really see the flaw. Except... I was looking for those pivot screws on knifekits.com, can't find them in the .156 variety. Discontinued or am I just too thick to look properly?
-
Woohooohhooooo maaan!! Some awesom work and idea! Hat down to you sir!!
Can't wait end result!!
-
:pok
thats all i have to say
-
Can't wait to see the result!

-
Just been through the whole thread. Good job so far
Yes stainless on stainless is not a good combination, especially with a close tollerance fit or 2 threaded bits. You can get special grease to stop it but in a knife it will eventually come out plus the fit of the pins inside tools would almost be too much of a close fit to even get a alayer of grease between tool and pin. I reckon i would try non stainless steel pins and get them zinc plated. although if you reckon the knife will get wet a lot then brass is probably the better option.
-
I know everyone here already said, but:
-It's AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
-Getting rid of the paper-thin scales and replace it for titanium is THE best idea for a Juice mod. It should be done by leatherman themselves!!!!!
-The thumb studs are a beautiful add to handling the tool
-I didn't understood why two wood blades but... still looking to be the best Juice ever!
-Someone said Leatherman should hire you. Well, THEY SHOULD!!!! You are doing mods that every juice owner wants.
Thank you Bob!!! And, FINISH IT, PLEASE!!!!!
-
-
I WAAANNTTT THEM!! Both mod's on my Spirit X!!!!!!

Who do I have to bribe???? :D :D :D :D ;) ;)
-

ah hem....

-
BUMPO!
I was looking to a much less invasive Juice mod (just making new stainless or g10 scales with pocket clip) and i was wondering how the brass pivots are working out.
I was also researching the thread size...4-40????
-
Got the brass pivots made a couple weeks ago (finally!) and did a test assembly. Everything works well, but I need to do a little polishing on some of the components before doing a 'final' assembly. (the donor tool was a used Xe6) Hopefully we got light at the end of this tunnel. :)
*screw size is 3-48
-
So, you might be sending it to me for xmas then? :D
-
-
NECRO THREAD!
I demand an update on the glorious SuperJuice...
-
It has been a while, I agree

There's talk in other far away places of this legend......
-
You can't just show the start of an awesome titanium mod here and not finish it. Trust me, I know. I admitted I needed help with my having of a life interfering with my titanium tinkering and MTO was here for me to push me through to the end.
We're here to help you Bob, with the pokey stick of encouragement but first you have to admit you need help.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




(or maybe not) :D