Slipjoint openers
-
Sparky, I have used some pieces of 1mm sheet metal, or cheap, blunt, blades, credit card multitools (the $1 ones), and of course pliers to open knives but I am always worried that I may scratch the blade I am opening.
I don’t know if a purposely designed opener will be less likely to slip and/or scratch… That’s why I was looking at the watch case openers, which should be strong enough, but soft at the same time (and cheap).
Sazabi, the only RRs I see are $18, with $29 shipping, to EU. Maybe these $5 are only for the US market. Sent me a link if you can.
-
A. G. Russell makes one. Don`t know if they ship outside the US.
-
Thanks to all, the RRs looks nice, but the cheaper ones don’t have non US shipping. Thanks for the offer Sazabi; I will keep it in mind, I still think $18 for a single RR blade is a bit over the top.
I am sure an ebay seller had them for much less, I remember seeing them some time ago, but he is probably out of stock curently, as he does not appear in the search.The money the A.G. Russel will probably cost, I should be able to pay someone to open the knives for me. :D
-
Well, if you try sniping, there is one for sale for $0.99 plus something like $4.25 shipping in the US; it ends in three days' time. :)
-
If you don't mind me asking where in the world are you Dks?
Looks like they are made from steel, I would have a go with my Dremel
I want one of these now ::) -
..it seems I will probably end up making one, and probably buying one of the cheap, yellow, watch openers to try. I have a wenger watchmaker's knife but it does not work well as a knife opener..
Its just a piece of metal, how hard can it be?? :D
PM sent to Sparky
-
@dks said:
Thanks to all, the RRs looks nice, but the cheaper ones don’t have non US shipping. Thanks for the offer Sazabi; I will keep it in mind, I still think $18 for a single RR blade is a bit over the top.
I am sure an ebay seller had them for much less, I remember seeing them some time ago, but he is probably out of stock curently, as he does not appear in the search.The money the A.G. Russel will probably cost, I should be able to pay someone to open the knives for me. :D
They start at 5.95 and go to 10.95 so that's pretty reasonable
-
@David said:
They start at 5.95 and go to 10.95 so that's pretty reasonableThat** is ** pretty reasonable. I could only find their knives on Ebay, so I made a guestimate based on these prices.

Thank to all for the sugestions, and to Sazabi and Sparky for their offers.

I have found an old latch and some door keys and I will see if I can turn them, with my limited skills, into knife openers.
If not then I will follow one of the other options the forum members sugested. -
You know we will need some pictures of how it turns out

-
…so I went ahead and made one, as it was said before, by others, it was not that hard.
Making a slipjoint opener.
I wore safety glasses, gloves and used an RCD.
Depending on the original shape of the metal you use, some steps can be omitted and other steps can be added.I wanted a *comparatively soft metal that would not scratch my knives * (I did not want, for example, a worn metal file), 1 to 2mm thick (to resist bending) and 1.5 to 2 cm wide (to fit in the nail nicks). The length had to be enough to provide good leverage, but not so long that it would be awkward to use and carry.
Part 1.
I finally settled on an old door latch.
It was 2mm thick, 2cm wide and **12cm ** long.It had a protruding spine, that added strength, but which needed to be flattened at its end. It also had a handle at the end that I had to remove.
I was able to bend the latch, with some effort, so I knew it had good elasticity and was made from a reasonably soft metal (steel).
continues...
-
Part 2.
I marked the latch and cut off the last bit, the bent handle of the latch that I did not need. I used a power tool but I could have just as easily used a metal saw (but that would have been less fun).continues..
-
Part 3.
I flattened one end with a hammer, removing the protruding spine and marked with a pencil the shape I wanted to give to the nail opener. I tried to imitate the shape of a thumb nail.continues..
-
Part 4.
I ground off the metal I did not want, shaping the knife opener.
I gave it a <u>blunt</u> chisel ground edge, at about 45 degrees, so that it would fit nicely in the nail nicks.I did the same to the other, narrower, end of the latch so that my knife opener has two usable nails, one narrow one wide.
I used a bench grinder (with two stones) for the shaping, but I could have also used an angle grinder (using a vise to hold the knife opener), or a metal saw.
I also used a rough sharpening stone and sandpaper to smoothen it a bit.
continues...
-
Part 5.
That Rough Rider Scout knife does not look so tough anymore! :DMany thanks to all!!

-
Looks like a good job Dks

-
That is cool dks, ive not seen these beofre but do have a few nail breakers so very handy

-
..and I saved money, i think... ???
... and managed not to hurt myself too!
Thanks for the comments, and sorry for taking up 4 posts instead of one; I dont have a picture account.
-
Nice work dks

I have several openers but they're never handy when I need them. I usually use the edge of a Penny when I need one.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login