Farmer with scissors and no gap
-
I'm afraid the saw backspring is very thin for the scissors.
Thanks again mate. -
The only thing I can think of, besides making one, would be to use 2 saw springs.
-
This might work but will turn out very expensive.
As you probably understand the problem is that there is not enough room for a new hole for the middle pin in the right position. I new from the beginning that the frames are incompatible but I hoped that I could open a new hole for the middle pin.
-
I don't think that would work either. If you did get it fit another problem would be that the alignment of the scissors to the backspring would be off.
-
Maybe but I can't understand why.
-
The backspring on the 91mm will be shorter than 93mm. Unless you move the hole position of the scissors to make up the difference.
-
Same is true for the 91mm backspring with the gap for the hook but it fits the 93mm frame together with the scissors. Of course both the holes of the backspring and the scissors need to be widen.
-
You said: Unless you move the hole position of the scissors to make up the difference.
You gave me an idea Steven.
What if I move the hole of the backspring on the right? Looks like there is enough room for a hole around 3mm to the right. Then maybe the middle hole will fit (with some drilling to make it wider of course).
Of course this way the backspring may not be perfectly flush with the other backsprings.Another thought is to grind the backspring to make a slot for the middle pin and then somehow use a stop pin between the liners around the backspring. That’s tricky.
-
I'm not aware of any easy way of adding scissors, except using the a 91mm hooked backspring :-\
It'd be cool if you found a way to do it without the gap in the back though 8)
You did the right thing pulling the Pioneer apart for the liner. Cutting them by hand is a very fiddly process :(
-
What I would try is to drill a new hole exactly where it needs to on the backspring. Then move the hole on the scissors to make the lock work. Looks like there is enough metal on the backspring to hold it in place. I will mock up a pic.
-
-
Drilling that backspring is going to give you fits. I'm still looking for a good way to open tool and blade holes up to 1/8" for bigger pins but the steel is so hard that diamond burs are the only option. I don't know how you would start a new hole without a carbide drill in a mill or very sturdy drill press. Also, welding is going to ruin the spring temper which would solve the drilling problem but over time they will just stay bent instead of springing back. Will the hook backspring work without modification?
-
Pm inbound
-
Thank you for your time Steven.
If you look closer to that pic you’ll see the problem. I will drill mostly the “air”.

Keep in mind that the hole in the pic is 2.5mm but I need a wider hole (3mm).
My thought is to drill a new hole here where the red dot is:

and keep the hole for the middle pin as is (same position but widen to 3mm).
This will move the backspring to the left (as seen at the photo) and will create other problems and then grinding to the other side of the backspring is required to fit the scissors. But that’s easier.bushidomosquito,
The only modification the hook backspring needs is to enlarge the hole from 2.5mm to 3mm.
And yes it’s very difficult to drill the backsprings.
It was hard to just widen the hole at 0.5mm. I can’t imagine the difficulty of drilling a new 3mm hole. Additionally total precision is required.
A buddy of mine has a machine-works (with lathes etc) so maybe I’ll go to him for the hole. -
I get the feeling that a custom scissor backspring for Alox that matches the scale contour might be worth a short run of parts. Not too hard to do with a waterjet cutter and drilling before the spring temper.
-
So I went back to the workshop a saw that my plan looks realizable.
Let’s do this.I widen the middle hole with a high speed steel drill and now it is 2.5mm
Using the saw backspring as a guide I drilled a new and precise hole on the scissors backspring. Continuous water pouring made the job easier because of the better heat removal.
3.2mm drill was required.
Fits perfectly with the liner.









-
I widen the hole of the scissors with a 3.2mm Cobalt drill. This is better than the HSS. The scissors steel looks harder than the backspring.
As expected the scissors doesn’t fit and now the fun of grinding beginns.
To be continued when I find time to grind the points I show with my finger to have a perfect fit and to allow the scissors to sit lower and in the right position.

















One is sure, that’s it’s possible to avoid the famous gap. It’s too much of a hassle though so think twice before you decide to use the old style backpring.
atb Aris
-
Very nice. I think this needs to be stickied with the rest.
-
Wow! HSS went through that spring without any problems? They must be softer than I thought.
-
One is sure, that’s it’s possible to avoid the famous gap. It’s too much of a hassle though so think twice before you decide to use the old style backpring.
atb Aris
Hats off to you for going the extra mile there

*
Call me lazy* but I think I'll stick with the hooked backsprings and just widening out the one hole ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
