Got Paracord?
-
Been reading this massive thread. Does anyone know how to cut paracord in a way that will not allow it to unravel? Right now I use wire cutters, which gives a clean cut, but then I have burn the end to keep it from unraveling. It doesn't look too good sometimes. Thanks.
-
You can buy a special cord cutting heated tool aimed at knot tyers in the US from only one company as far as I am aware it has a heated blade so cuts and seals at the same time very handy gadget got mine from the states they run off a standard AA battery but are effective all the same.
-
I usually cut it with something sharp, then I burn the very tip and before it cools down I press it onto a smooth piece of metal so it becomes flat.
-
The problem with burning the end is that it blackens the end and 'uglifies' it. Using a special heat source may work better. I use a lighter.
@rayraychil
Can you provide a link to that cutting tool? -
@preahkumpii said:
Been reading this massive thread. Does anyone know how to cut paracord in a way that will not allow it to unravel? Right now I use wire cutters, which gives a clean cut, but then I have burn the end to keep it from unraveling. It doesn't look too good sometimes. Thanks.I use the blade on my Helmsman to cut the cord on my projects and if you are patient, you can use a lighter to singe the ends without turning them black...hold the lighter just close enough to melt the cord end but not in the flame.
-
Take an old knife and heat it up till it glows red. It will seal the paracord as it melts its way through.
-
You can get a knife cutting bit for soldering irons, I keep meaning to buy one.
-
@preahkumpii said:
Been reading this massive thread. Does anyone know how to cut paracord in a way that will not allow it to unravel? Right now I use wire cutters, which gives a clean cut, but then I have burn the end to keep it from unraveling. It doesn't look too good sometimes. Thanks.As others have said heat an old blade. I use old crappy fake SAK and heat it over the gas hob; works a treat

-
Just FYI, I found an excellent tool to use for cutting the cord and making it look good. I actually cut the cord with a pair of wire cutters. This leaves a clean cut. I suppose you could also use a razor blade. Then, I found a hand-held butane blow torch at Lowe's. It was $20. It makes a nice blue flame that when lightly touched against the clean cut of the cord melts it without much discoloration or "ugliness."
-
A simple one, but I think it's gorgeous! :) The paracord fob is nice too. :D

-
A simple one, but I think it's gorgeous! :) The paracord fob is nice too. :D

Is that a Skipper or the other blue one?
That's the Helmsman. Differences from the Skipper: No pliers, backspring phillips and awl, no corkscrew.
-
A simple one, but I think it's gorgeous! :) The paracord fob is nice too. :D

Is that a Skipper or the other blue one?
That's the Helmsman. Differences from the Skipper: No pliers, backspring phillips and awl, no corkscrew.
Yeah, I knew it was thinner, with a few less tools.
But don't you just love those textured blue scales? -
Here's a few I did. Sorry for the crappy pics.




The last 2 are reflective paracord. Shot with flash to show the difference.
-
Some new stuff:










-
In support of the WUSA tomorrow in the finals.


-
dang, you guys are good. I just recently started doing them knots, but I see now that I need much, much more practice, aside from the fact that I cant seem to get paracord still.
Last thing I made was a monkey fist on a shoestring budget, quite literaly as I did use a shoe string. I will put some pics up later.
-
double post, cant it be edited??
Ok, I have here a pic of a monkey fist with snake weave with a shoe string, not the best of examples, but not bad for a first run.
also, my current inability to get paracord of any other color than white is limiting my current offerings.
I must reiterate the past post, I have ways to go b4 I can make the stuff I have seen here, but hey pratice makes perfect afterall.

keep up the good work (and providing me with expamples :) )
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



