Farmer with scissors and no gap
-
Excellent work harry.

(thread title changed as well) :)
-
I am not 100% sure but the back spring from a 93mm solo (without awl) would probably fit. I recall that I tried this some time ago but did not finish since the hole for the rivet needed to be widened (93mm uses larger rivets) and I seldom need scissors and also the handle for the scissors might need some minor adjustment in order to close the knife nicely. On the upside 93mm solos with abused blades seems quite common and cheap, so no need to sacrifice a new knife for this. If it works, that is....
-
What you said makes perfect sense.
I have just measured the thickness of the blade backspring and it is 2.7mm.
The scissors backspring is 2.5mm so it could fit with a very thin washer.
If some adjustments are required is another story and this is probably an easy job.Problem is that the blade backspring is longer than the scissors so maybe the scissors will sit too low.
Keep in mind that the scissors are designed for 91mm frame so they are quite short.
But there has to be a solution to this problem. A new hole on the scissors is maybe not possible but we could make something like a step for the scissors tip to rest on… something like a slightly bent liner or whatever.I have not pinned the knife yet so maybe I should try a solo backspring to see if it works.
-
After so intense thought on this. I think the best option would be to take a solid block of stainless steel and mill it down to the correct liner size. Then upon request we could cut layers off as needed. So hows that?
-
Another idea would be to use the spare backspring and blade from the Pioneer liner donor.
If I cut the blade where the black line is near the pivot hole there will be enough support for the scissors tip.

this way it’s like having a two piece liner and not a solid one.
So no need to use a fourth knife for one project. I have already used three SAKs for this.
-
Thats a good idea. Just out of curiosity I wonder how long the scissors are on the swiss tools?
-
I had to try the Solo idea so I disassembled the unpinned knife and tried the saw backspring together with the blade.
This backspring is very thin but this does not matter for the test.The blade sits nicely so I assume the backspring of the Solo has the same basic shape.

Then I tried the scissors and as expected they sat too low and disappear inside the body of the SAK.

The difference in height between the two springs is obvious. The scissors need a high backspring to rest.

So maybe the idea of the Solo backspring has to be abandoned unless we could do modifications, unknown at the moment. But only if I have the real Solo backspring I can tell for sure.
Like I said previously the problem is that the scissors are too short for the 93mm frame.
-
I love the Farmer, its a great tool, with the addition of scissors this is one very useful SAK. Excellent post, very enjoyable to read and see the brilliant end results.
-
And the finished knife:




-
Great pictures Harry, a very cool Farmer indeed.
-
Food for thought. What about using a backspring from 111mm knives.
-
Frankly, if you do the cost benefit analysis somebody could design a 93mm scissor backspring, have a buttload of them water cut and finish them in a mass media tumbler at around $3 each. They would sell for around $20 when guys will buy a 30$ knife just to get a part they want. And why stop there? Alox backsprings for pliers, magnifier and phillips driver, Cybertool driver. Hell, just go ahead and imagine an Alox Workchamp. This could be a nice little business for someone. Don't make me do it. I've already got enough on my plate.
-
@bushidomosquito said:
Frankly, if you do the cost benefit analysis somebody could design a 93mm scissor backspring, have a buttload of them water cut and finish them in a mass media tumbler at around $3 each. They would sell for around $20 when guys will buy a 30$ knife just to get a part they want. And why stop there? Alox backsprings for pliers, magnifier and phillips driver, Cybertool driver. Hell, just go ahead and imagine an Alox Workchamp. This could be a nice little business for someone. Don't make me do it. I've already got enough on my plate.I dare you, no I double dog dare you. Do it!
-
Don't think I won't. >:D
-
@bushidomosquito said:
Don't think I won't. >:DYou dont have a hair on your chest if you dont. :P

-
Don't think I won't. >:D
You dont have a hair on your chest if you dont. :P



-
@bushidomosquito said:
Frankly, if you do the cost benefit analysis somebody could design a 93mm scissor backspring, have a buttload of them water cut and finish them in a mass media tumbler at around $3 each. They would sell for around $20 when guys will buy a 30$ knife just to get a part they want. And why stop there? Alox backsprings for pliers, magnifier and phillips driver, Cybertool driver. Hell, just go ahead and imagine an Alox Workchamp. This could be a nice little business for someone. Don't make me do it. I've already got enough on my plate.That would be very cool. Now let's find a volunteer!
By the way, how about using a scissors & long nail file layer? Of course, the long nail file would still be too short for the 93mm frame, but perhaps it would be easier to make that specific spring fit? The liners would need extra pivot holes for the nail file.
-
:D So go ahead and make some nice backsprings!
May I have one or two please? I'm fed up with grinding! >:( :D
-
I'll take 2 also. And while you're at it make some file, inline screwdriver/mag glass, and saw back springs.
-
You gotta be kidding me, right?
I'm still having nightmares of me with a file and enless grinding incompatible backsprings :ahhh :ahhh :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login