Leatherman Kick pocket clip de-wobble
-
I tried the paper and the o-ring the o-ring worked better me also good mod thanks for searing.
Mike -
I tried the O ring mod on my Kick the other day. It worked great, but my o-ring was a little too large so I tried experimenting with other materials.
I think I found another simple way to dewobble the Kick clip.
All I did was place a small metal washer between the clip and screw. Seems to work just as well as the O ring on my Kick at least.
If the action becomes too tight and it is hard to access the phillips, you can loosen the knurled screw on the other side a tad with another clip or some pliers.
The clip has an extremely small amount of side-to-side motion afterward, similar to the O ring version.
You can tighten it until there is no motion, but it makes the tools very hard to get out of that handle.
-
@DaveK said:
Sorted! Well sort of.I started looking at this ages ago, but having a short attention span must have found something more interesting to do.
The problem is, basically that the thickness of the clip is less than the depth of the head of the threaded rivet that the clip screw attaches to, if you see what I mean. So even if you tighten the clip screw up very firmly, the clip itself still rattles about. Like Spoonrobot says wibbly/wobbly.
So, the solution is to pad the clip with a washer so that the clip screw meets it properly. It works!
I've taken a couple of pics of what I just did, but irritatingly, the batteries just died on my camera :-[
When I can power the camera back up - I'll post 'em up so you can see what I'm banging on about.
Hi DaveK,
I don't have a Leatherman Kick (yet), but if I may offer a suggestion... use a lock washer instead of a standard flat washer or even a nylon one. The lock washer will have the 'bite' to prevent the clip from moving.
Caution! May scratch surfaces. (But the scratch surface is only around the washer area, which won't be visible anyway)
@DaveK said:
Well I found some O-rings that fit the bill, and they work perfectly!I found that if I tighten the clips too much, then that does reduce the wobble, but there is a trade off as the bottle-opener and crosspoint driver become too tight to open comfortably, so by simply adjusting the tension on the pocket-clip screw, I eventually found a nice balance.
The elasticity in the rubber O-ring means that although the clip can be moved left to right if you force it, it will actually snap back to where you positioned it when released. You could think of the lateral movement as similar to the vertical movement of the clip - i.e. if you get your nail under the end of the clip, pull and release, it snaps back down.
Yup - that'll do for me.
I have used a slightly larger O ring on the BO Kick in the pictures, that's why the clip appears a bit more raised - I'm not sure which I prefer just yet.....
I've added some pics, but they're not very exciting :D
If you prefer using an o-ring instead, why not get those rubber gaskets that are used in water taps/shower heads? They are also rubber, but they are flat on both sides. It will look better (subjective) than an o-ring which looks like it is bulging out of the clip/screw when flattened.
k
-
Whoah, thread necro. :ahhh
-
Just thought of another idea but I will try it out to see if it works first.
@CENTURION said:
Whoah, thread necro. :ahhhSorry what does this mean? Something like bringing back a buried thread?

-
Just thought of another idea but I will try it out to see if it works first.
Whoah, thread necro. :ahhh
Sorry what does this mean? Something like bringing back a buried thread?

Yes, but that's not a problem around here..

Thanks man.

I always run a search to avoid starting duplicate threads. Allows me to see what has been done and how to improve. So I often find myself reading buried threads. The best thing about them is that they are already filled with inputs from members. I learnt alot from here, and I intend to share some of my ideas too, so you will see more unearthing of threads... :D
@sparky415 said:
We need to see this other idea (with pictures please)Belting it with a hammer was my idea

Yes you will :) I have a couple of clips and a kick on order right now. Need to see how much is the clearance first. Wasn't my intention to do this actually but it appears that this is an issue that needs to be addressed. OTOH, it seems like many people are having fun with those mods! So I thought I'd join in.
In the meantime, maybe others can try out my suggestions above and see if it works... or chip in with better ideas!

-
Well this is taking longer than expected. Items still in the mail, but in the meantime, I thought of other ways to fill the gap.
One is to get gasket sheets that are used in engines, some come in a sheet where you can cut out to your desired shape/size. It has varying thickness and materials, some have steel content and some are more like paper.
Another alternative is to get paper hole reinforcement stickers, these can be found in stationery stores. They are adhesive so it's easy to stick. Want it thick, just stick another one on top of the existing layer. If you can't find large ones, just get a larger paper punch to punch out the right size for the screw.
Hope this can help someone! If you use any of these methods please reply to let us know its effectiveness! :)

-
@DaveK said:
Sorry - should have said....I found a selection of assorted orings in a branch of Maplins (don't know if you have them over there - a bit like radio shack really). Cost me £2.99 ($6) for 225 assorted rings!
Sorry for all you imperialists (?) out there but the measurements in the pictures are all in metric......
DaveK do you have any of these o rings left that I could purchase a dozen or so for use on my kick pocket clip issue as I won't use 225 and I am sure you won't have used them either.
Ray -
The best solution imo is beating the clip gently around the side of the Kick with a small hammer.. :)
My clip can't move as much as a milimeter..
-
Good show Allan!
Sometimes the simplest solutions are the best ones. :) -
I just received my Kick Clip and when I did a direct install it was loose as could be and I was not going to leave it like that. I remembered I had some tubing that I was hoping would work for my needs. I had two different sizes and it turns out the bigger one fit perfectly. I first tried to cut a piece off with scissors but I could not get a thin enough piece so I used the Kick's blade to slice off a piece. The piece I ended up using was thinner than the one pictured.

Next up was the thread lock.


I then had to get out the trust Wave and the Torx Bit Kit to tighten the screw.


I tightened the screw and we are good to go. Well not quite. I tightened it so much that I could not get the Phillips or the Can Opener to deploy. I think I found a good median between how tight the screw is and how hard the tools are to deploy. I am going to let the lock tight dry and we are good to go.

-
That is cool!
Let us know how it works out for you. 
-
Did you use fish tank breather plastic hose and approx what was the dia in mm please as this loose pocket clip issue has been driving me nuts so I would value your advice as your mod seems to be the best out of the lot imo could not get hold of any small silcone washers.
regards
Ray -
@rayraychil said:
Did you use fish tank breather plastic hose and approx what was the dia in mm please as this loose pocket clip issue has been driving me nuts so I would value your advice as your mod seems to be the best out of the lot imo could not get hold of any small silcone washers.
regards
RayThe clip on the BO Kick is "Pre-Beaten" by Leatherman and doing the same yourself is the best permanent solution imo.. Have you tried it?
-
@rayraychil said:
Did you use fish tank breather plastic hose and approx what was the dia in mm please as this loose pocket clip issue has been driving me nuts so I would value your advice as your mod seems to be the best out of the lot imo could not get hold of any small silcone washers.regards
RayIt is 1/4"ID X 3/8"OD (166) I have no idea if it was for a fish tank. I bought it by the foot at my local hardware store. It has worked perfectly and I am very happy with how it is holding up. I will also add before I screwed it on I bent the actual clip to give it better retention in my pocket. Hope this could help. If you have any other questions please ask.
-
Vise Grip works great. Allen must be a finish carpenter because i would destroy the poor little LM with a hammer. Thanks to Multimat again for steering me in the right direction,and Pics posted by AHB made the light bulb flicker im my head.
I used 8" Vise Grips for better leverage. The teeth on the plier head grip well on the clip and clip only. No more play in the clip.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


