Style CS problem
-
First time I've seen that, though you've just had me pull mine out of my pocket to check (nothing wrong with mine thankfully).
can't think of any reasonable way of repairing that I'm afraid, it really needs to go back to your Leatherman distributor.
-
Looks like perhaps a weak point/flaw in the casting. Successful repair is unlikely. Warranty replacement with the help of a regional Leatherman distributor is the best option.
-
I am, glad it is not a common problem; I was quite happy with the little thing, until it broke.
I thought the casting/metal quality could be the problem; the metal at the cut had a "porous" look, like cast iron.
As I said in previous posts the local distributor will charge me at least, if I remember correctly, 30 euro for a “free” replacement. The policies of LM USA are a lot different from the policies of their overseas distributors, unfortunately.
SuperGlue to the rescue......
-
That sucks... I thought the warranty was more straight forward than that :(
-
If you had small metal, drills, and rivets you could fabricate another spline there (between the handles). Not sure if it worth that much trouble to you or not since you said the shipping for warranty work was too expensive.
-
@Xelkos said:
If you had small metal, drills, and rivets you could fabricate another spline there (between the handles). Not sure if it worth that much trouble to you or not since you said the shipping for warranty work was too expensive.I thought about that too, gluing a secondary spine and attaching the broken bit to it, though that may affect the functioning of the tool. Rivets will probably be even more obtrusive.
Locally the Micra, for example, sells for 50 euro, as I remember, so 30 Euro for a replacement new? one is not that bad.
Other, more expensive models will also be replaced for the same amount, so it makes a bit of sense, if you buy locally. However when buying from the US or even amazon uk, for the cost of a replacement here you can buy a new one, anyway. -
if you don't have any luck fixing up the broken one you could always look to EDCsource, Neil has one for sale that works out at just a little more than 18 euro's plus P&P. Going to be a lot less than getting one from the local distributor at 30 euro's. :-\
-
i lost mine. =(
i warn you all that it can and will eventually fall of your keychain.
-
All these just prove the superiority of the Micra!! :D
-
The metal at the break point has a "crystallized" look to it, suggesting that it was too hard/brittle. Probably the fault of an improper tempering after heat treat. :( That component should be springy and flexible, not hard and brittle. :-\
-
@J-sews said:
The metal at the break point has a "crystallized" look to it, suggesting that it was too hard/brittle. Probably the fault of an improper tempering after heat treat. :( That component should be springy and flexible, not hard and brittle. :-\Good call Bob - I initially thought casting impurities though. How are those parts manufactured? The internal corners look a little too crisp to be formed and I'd have expected the corner section to have thinned through stretching too if they were coined in a press. Either way I'd agree it's a metallurgical flaw that ought to go back to LM.
Have you tried just emailing LM the pics dks? If you explain the costs involved in sending it off being the price of a new one, they might just send one on the back of the pics alone.
Worth a try ...

-
@50ft-trad said:
The metal at the break point has a "crystallized" look to it, suggesting that it was too hard/brittle. Probably the fault of an improper tempering after heat treat. :( That component should be springy and flexible, not hard and brittle. :-\
Have you tried just emailing LM the pics dks? If you explain the costs involved in sending it off being the price of a new one, they might just send one on the back of the pics alone.
Worth a try ...

If mine is the only one to have had such a problem, does it make it collectable???? I am open to offers :D
I may try contacting them; I am usually lazy in that sort of situations; I only got this in a lot in which I was bidding for a CS4 and it is a low cost tool.... I just can not usually be bothered with the questioning and the agro involved that will probably end up with being told to contact the local dealer.
I will see if I can motivate myself to do it, or maybe I will just get another one…
-
Would a glob of JB Weld be able to hold it together?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login