Titanium SAK progress...
-
-
With the scales and liners polished up I turn my attention to enlarging and honing the tool pivot holes to .127" and then mirror polishing them with some green buffing compound on half a cotton swab in a Dremel tool. Even though the pins are a harder titanium alloy I don't want to give them a surface to gall onto.It is tedious to open up all these holes with a diamond reamer but I'm stuck on using 1/8" pins. Now I have to make a bunch of .005" phosphor bronze washers to keep the tools from riding directly on the liners.

-
Nice thread this 8)
-
nice! -
Autoclave safe Titanium toothpick and tweezers for my little orange G10 Classic. They are both longer and wider than the usual SAK implements. The tweezers have passed the girlfriend eyebrow pluck test with flying colors. She says that a girl has to search high and low to find a tweezer that works this well. I told her that tonight she gets steak and corn on the cob for phase 2 of the testing.

-
Woah! Ti SAK..... yes, I think we like this :D
-
Your work is very impressive. Congrats mate!
However the Titanium toothpick may hurt the poor girl's teeth. -
Passing the eyebrow test is praise indeed

She's right, the number of cosmetic tweezers that just don't work on fine hair is quite ridiculous ::) They can often be saved with a bit of sandpaper but you shouldn't have to.
-
They were a bitch to make. I'm going to have them and the toothpicks EDMed from now on from one piece and to the dimensions of the originals so they will fit cellidor scales if someone just wants them for a regular SAK. Then all I have to do is make jigs to sand the slant on the head and bend them out.
-

Man that tweezer looks amazing
Really nice job mate 
But now I gotta save for the Ti liners AND a couple of tweezers. No more
weekends, NOOOOOOO :ahhh -
@bushidomosquito said:
They were a bitch to make. I'm going to have them and the toothpicks EDMed from now on from one piece and to the dimensions of the originals so they will fit cellidor scales if someone just wants them for a regular SAK. Then all I have to do is make jigs to sand the slant on the head and bend them out.You're going to have the tweezers EDMed from now on? How did you make these ones then? :o
Most impressive work.

-
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.
-
@bushidomosquito said:
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.Wow.

-
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.
Wow.

x10

-
I didn't notice the rivets until you mentioned it. Very meticulous work

-
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.
Wow.

x10

+1 amazing work!! congrats

-


Carbon fiber and orange G10 with hardware to space the liners apart for finish sanding. -
OOOO pretty!
I can't wait for you to work some magic on my G10 scales!
-
Bushi you did not make those wee Torx like fasteners did you
.If , I know slim chance you didn't make them :ahhh :ahhh :D :D, were did ya gets them from
8) 8) 8).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
