ST 300 owners club
-
Say something Dunc...
:D
My ST300 is tight so I haven't seen that before..
-
I'm camera shy :-[ lol everything is tight , it's just the handles overlap each other when applying any torque when using the drivers .
-
@Dunc said:
I'm happy with it but not sure about the handle movement when the tool is closed
There is no play in the tools or pliers but I don't like how the handles can overlap each other when using the drivers . Is this normal ?I believe it is, both of mine do this. It looks to be a combination of the gap between the tools causing just the small surface of the handles to make the only contact, combined with the flex in the steel of the handles themselves. Any sideways force (especially the twisting motion of a driver) instantly causes the overlap.
Disappointing design flaw...
-
-
I'm camera shy :-[ lol everything is tight , it's just the handles overlap each other when applying any torque when using the drivers .
Whoops, my bad mine does that too.. :P
You could try posting the vid on LMs FB page to see what they say.
My iPod won't allow me to upload video direct to FB , I'll try later on . Can't see any way of improving it though

-
As replied on LM's Facebook page. BTW, Leatherman are moving stuff to Salt Lake City for the convention this weekend so replies may be slow or after the weekend. That's quite a drive across Oregon, base of Idaho, and half way through Utah.
@Duncan Moore said:
Got a Supertool 300 yesterday , I really like it but not keen on how the handles can overlap each other when applying torque on the drivers .Have two, one has not been used.
Neither has any play between the handles. However both have play only in the closed position rubbing them side to side - with some effort. Since the handles are necked-down to the thin pliers that would make sense, as the pliers pivot axis in inside the handles. The only support is on the knurled handle bolts and the plier jaws play within the handles.
Once the pliers pivot axis is on the other side (pliers deployed) there is no play since the handle wedges are engaged and act on the pliers pivot. If there was play in the pliers pivot then there would be play in the handles in this fashion.
When torquing at a 45° angle you are applying pressure on the pliers, the weaker necked-down area, and the bolts. Still thin metal compared to a proper torquing tool which is at least 1/2" solid all around at minimum.Noticed that even the Charge and Wave handles will move side to with some effort. Would surmise that most any multitool would when used a lot would. More so if bent out of alignment when torquing.
-
Yes your right , when the pliers are deployed there is zero play . My other slight issue that can be seen at the start of my video is that when the pliers are closed there seems to be a high spot somewhere so if you push the plier end together it rocks and the other end opens up a couple of mills . Hard to explain and a little picky but kind of makes the tool rattle a bit .
-
Hi Dunc, after watching your video and the movement of your handles when closed, your ST300 is very similar to mines. I don't have as much play in mines but there is a little and the handles are slightly offset when closed. But also like yours when the pliers are open there is no play at all.
-
Thanks Colin :)
-
@Xelkos said:
...Once the pliers pivot axis is on the other side (pliers deployed) there is no play since the handle wedges are engaged and act on the pliers pivot. If there was play in the pliers pivot then there would be play in the handles in this fashion...Actually the play is still there, although somewhat minimized, and less perceptible with the the plier cams "locked". You can verify this by mounting one handle of the open tool in a soft jawed vice, and then mounting a stationary measuring device (dial gauge, or ruler) against the end of the other handle, I found that the steel still does flex about the same amount as with the tool closed.
Noticed that even the Charge and Wave handles will move side to with some effort. Would surmise that most any multitool would when used a lot would. More so if bent out of alignment when torquing.
It does seem somewhat more exaggerated with the ST300, what with the small contact area between the handles when closed.
-
Leatherman made a post yesterday in reply to Dunc:
@Leatherman said:
Hey Duncan-
We did that to give maximum flexibility to the handles when you're really squeezing on them but not too much to th epoint where they fold on you. Mine here at my desk are the same way and they work perfectly. -
I want to buy a bit adapter for it . Is it just the std one that fits the Fuse/Blast etc. or is there a specfic one for the ST300.
thanks
Dunc
-
@Dunc said:
I want to buy a bit adapter for it . Is it just the std one that fits the Fuse/Blast etc. or is there a specfic one for the ST300.thanks
Dunc
Two options, depends on how much torque you want.
Removable Bit Driver - Silver or new Black Oxide

This one fits over the square Phillips driver. More readily available. Have not heard of anyone breaking one (yet) but is looks like cast alloy.A personal photo showing both ends and the side view.

Have used this on just about every Leatherman tool, including the PST - which needs pushed in more. It <u>will</u> fit in the large bit driver using the 1/4" x 6mm bit - use the 1/4" for the RBD. Filed mine down more for convenience to fit it onto my Surge.

Photo with the 1/4" x 6mm bit adapter, Bit Extender, a 1/4" socket adapter that I carry in the RBD plastic bit card (two empty vertical slots) into my Surge. Each connection does a wiggle some. Wanted to show that the RBD can be used as a 1/4" bit adapter with other Leatherman tools that have a Large Bit Driver - was not advertised by Leatherman prior to my posting on their facebook page. :D

Then there is the more heavy duty, yet the attachment isn't tight... Universal Tool Adapter (rare)

-
Wow thanks for the detailed reply
I already have a universal bit adapter but I want one that will fit in the ST300 nylon sheath .Cheers mate I'll order one now 
-
@Xelkos said:
Leatherman made a post yesterday in reply to Dunc:@Leatherman said:
Hey Duncan-We did that to give maximum flexibility to the handles when you're really squeezing on them but not too much to th epoint where they fold on you. Mine here at my desk are the same way and they work perfectly.
This does make sense. One of the inherent qualities of the design of the Core, with it's layered handles, is a natural cushioning effect. Engineering an intentional flex, or "spring" into the solid metal handles of the ST300, would be a smart way to duplicate the feature.
Takes away somewhat from the "solid as a rock" feel, but adds much to the day to day usability.
-
New ST 300 owner reportin for duty. Having owned the powerlock and crunch I find its a very substantial tool compared to the Powerlock. Re: flexy handle I quite like it as it gives me an indication if I am squezing the handles too hard.
Powerlock relagated to BOB duty with th Crunch.
The crunh was my first Leatherman and boy one feature i LOVE about the Crunch is the precision snick in the tool deployment and also the same schnick in the return.
I wish the ST 300 had this level of precision but I understand its a beefed up tool for hard work.
I love the pliers and the tool loadout. I tested the cutters cutting through a multistrand wire from an old bike lock.
Bike lock 0 : ST 300 1
Excellent tool
-
Welcome to the club roguesw!

-
Thanks J-sews

-
Add me to the ST-300 club.
Glad to be here. -
Yep I'm in too. Had a Wave for a while but kept getting let down by that removable bit set-up. Just no depth to reach a recessed screws and a 3D driver. It has all the tools I need (i can survive without the glasses screw driver :)) Also I found with the Wave if you get it covered in dirt it's hard to get out completely but with the 300 it's Sooo much easier.
I'm not knocking the Wave it's a well made tool. But I just like a good basic, tough no nonsense tool. I just hope they keep making them in some form or another. ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login