Thinking About a Mora: Suggestions?
-
@dks said:
Just like my other thicker sharp grind angle knives (even the SRM 763) it starts well but after the first few mm into the apple it starts to want to snap the apple in half, like driving a wedge through it, rather than slice it. It needs a lot of force to go through. It gets, in a way, stuck. Meat is soft so it accommodates that extra thickness well, allowing the knife to continue cutting.Something like this, I would imagine:

-
Yeah I can see that happening with an apple and that grind.
-
Wait wait wait, I'm confused. I think I just skimmed through the thread and... am I reading this right?
He asked for a Mora and ended up with ONE?
Why didn't he buy like 5 to try, I'm so lost...This is the right place right? Am I still at MT.O? :ahhh
-
Well, it arrived today, and I must say that I'm impressed (when I consider the price, I'm very impressed).
-
Fits a big hand well
-
Firm, comfortable, non-slip grip
-
Good balance, not heavy in the handle, but stays in your hand when you open your fingers
-
Super sharp
-
Love the carbon steel, has a real "old world" look and feel to it







-
-
Very nice mate, I'm sure it'll serve you well.

-
Moras are like dogs, if you don't like them, there's something wrong with you :P
-
They take a scary edge too!

They work hard without complaint. My only issue is how quick they start to rust after getting wet. Make sure it's DRY DRY DRY and oiled before being put away. -
My pocket sharpener arrived today, got the DMT F70F because I didn't have a pocket sharpener that would handle a Scandinavian Grind.
I ran the blade across it a few times, and I must say that sharpening a Scandinavian Grind almost feels like cheating. I'm thinking that a blindfolded blind man could put a good edge on one of these.
Also, this is my first "diamond stone" (I do have rods, but no flat diamond stones), and I had no idea how well they cut the metal compared to a traditional one. I'm thinking that I may retie my GATCO in favor of the Lansky diamond set. Time to save my pennies...
One caveat though, with the DMT F70F having the diamond surface right out to the very edge, all it takes is a slight rub to scratch the blade surface (at least with the carbon steel)

-
@django.cj said:
They take a scary edge too!
They work hard without complaint. My only issue is how quick they start to rust after getting wet. Make sure it's DRY DRY DRY and oiled before being put away.Yea, I'm starting to notice that with just handling that the tiny imperfections of the blade surface are starting to darken. I think that I may get the vinegar out and patina the blade.
Anyone have any experience with this preventing rust on these blades?
-
A patina will protect a blade from developing orange rust to an extent, but you still have to keep it dry and wipe it down with oil occasionally.

-
Thanks...that's home-squeezed Spork-dex :D
-
They take a scary edge too!

They work hard without complaint. My only issue is how quick they start to rust after getting wet. Make sure it's DRY DRY DRY and oiled before being put away.Yea, I'm starting to notice that with just handling that the tiny imperfections of the blade surface are starting to darken. I think that I may get the vinegar out and patina the blade.
Anyone have any experience with this preventing rust on these blades?
I use a very light coat of gun oil on mine, just a drop or two rubbed all over. It works well.
The rust/discoloring isn't bad, when it happens (usually after camping) I just use a scotch-brite pad to buff it out. -
I use mineral oil because it is food safe.
-
Well I've decided on the vinegar patina, got is soaking right now. Wife gave me that "you're nuts" look when I was sizing up a cup to put it in.
Interesting that when I first dipped it in the vinegar, I pulled it out a few seconds later and some areas began to instantly oxidize.
I'll post a finished pic later.
-
@turnsouth said:
Well I've decided on the vinegar patina, got is soaking right now. Wife gave me that "you're nuts" look when I was sizing up a cup to put it in.Interesting that when I first dipped it in the vinegar, I pulled it out a few seconds later and some areas began to instantly oxidize.
I'll post a finished pic later.
The other thing you could try is carnauba wax. $6 at a woodworking store for some pure wax will give you enough to last for... many lifetimes on a knife blade. It's also food safe (M&Ms are coated in the stuff).
-
Patina pics:


-
They do turn pretty grey when done that way.
You might take a bit of steel wool or some other
Light abrasive and take some of it off? It will give
It more of a vintage antique look?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

