What Did You Use Your Multitool For Today?
-
Today at work I used my Legend 800 to cut metal strapping, used the scissors to cut cable ties, the knife to open boxes, the pliers to twist the ends of a small piece of wire together.
At home I used the saw to cut down three trees (well, more like small shrubs), the scissors to prune a climbing rose bush, and also the scissors to prune a few out of control grape vines. Oh, I also used the cutters to snip the ends off of my jigsaw blades so they will close with no interference.
-
I used my BO sog file to round off some old SAK rivets to disassemble it.
-
My Blast with the bit driver attached was the champ of some Irene cleanup tonight. I used it to dismantle some shelving and a display case, as well as some waterlogged furniture that had to be broken down.
-
I used my blast to pull a shard of metal out of my tire today. I spent the next 20 minutes trying to line up the reamer in the hole, as it was at a pretty good angle and I couldn't get the plug in. My new gerber hatchet came in quite handy as a hammer to push the reamer thru the hole. Plugged and holding air now!
-
@jerseydevil said:
My Blast with the bit driver attached was the champ of some Irene cleanup tonight. I used it to dismantle some shelving and a display case, as well as some waterlogged furniture that had to be broken down.I sure hope no MT's got wet. :(
-
@captain spaulding said:
My Blast with the bit driver attached was the champ of some Irene cleanup tonight. I used it to dismantle some shelving and a display case, as well as some waterlogged furniture that had to be broken down.
I sure hope no MT's got wet. :(
I think we all learned to keep our multitools away from pots of boiling water

-
Spirit pry tool opened a can of paint and awl popped some drain holes around the rim of said can, went through like butter!
-
The scissor spring on my PS4 broke today so I decided to replace the scissors with a cut down key. I used the VIC Mountaineers metal file to ground the key down. A little SAK on Multi violence. >:D Now I just hav to choose a mini flashlight to go with this mini keychain setup, maybe the DQG?



-
I used my Leatheman in an attempt to fix my Gerber.
-
It's a new Sports 400 Gerber I received yesterday and the blade nick was on the inside.I was going to swap the blade to the other side but it wouldn't clear the retractable pliers so it went back in the original
position.I guess I can live with it. -
@Chain Gang said:
It's a new Sports 400 Gerber I received yesterday and the blade nick was on the inside.I was going to swap the blade to the other side but it wouldn't clear the retractable pliers so it went back in the original
position.I guess I can live with it.Why don't you send it in to Gerber for some warranty work?
-
I had a flat tire yesterday, I used my blast to pull the shard of metal out of the tire, and my LM C33X to cut the plug flush once it was installed. All in all, a very hot and sweaty job considering the ridiculous heat and the stupid angle of the hole. I couldn't for the life of me get the darn reamer to go in, and once I did, the plug just didn't want to go either. At least I was able to repair the tire, couldn't have done it without my Leatherman!
I used the same blast today to pull a bunch of packing staples out of a huge box. One of them caught my finger and now I have a nice chunk missing.
I then used the blast again to grip a stubborn bolt on a grille guard (no sockets or wrenches in reach) and loosened it enough to remove it by hand.
-
@captain spaulding said:
@Chain Gang said:
It's a new Sports 400 Gerber I received yesterday and the blade nick was on the inside.I was going to swap the blade to the other side but it wouldn't clear the retractable pliers so it went back in the original
position.I guess I can live with it.Why don't you send it in to Gerber for some warranty work?
From what I read they all are coming like that.No problem opening the blade so I will live with it.
-
@Chain Gang said:
@captain spaulding said:
@Chain Gang said:
It's a new Sports 400 Gerber I received yesterday and the blade nick was on the inside.I was going to swap the blade to the other side but it wouldn't clear the retractable pliers so it went back in the original
position.I guess I can live with it.Why don't you send it in to Gerber for some warranty work?
From what I read they all are coming like that.No problem opening the blade so I will live with it.
O alright I thought it was a defect. If it is not a big deal than I would leave it as well.
-
just photos today with the leatherman super tool 300
-
I thought the headphones connector on my smartphone was broken but it turned out there was just some fluff (?) from my jeans stuck inside :D
My Vic Classic's toothpick took care of it :) -
I just used a Crunch to remove that safety strip of metal which covers the flint on a new bic lighter.
I don't have kids, just a dog, and if he is smart enough to get that thing lit without thumbs, I reckon he is smart enough not to burn the house down :D
-
Well I was extremely bored and my pain med's are making me feel very loopy so I made a little stand out of paper clips for this slice of rock I have. It was made very quick and with not very much precision. Thank you Super Tool.


-
Used my new wave to pull some nails out of an old piece of plywood. Sure would have liked to had that mj hammer on it though ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login