Leatherman MUT Owners Club
-
Has anyone thought about removing the belt clip?
I for one don't use it at all. I'd rather pocket it completely or use the carabiner.
I just don't know what to do with the holes because you can't just put the screws back in as they would stand out too far.

On the other hand I'd really hate to "modify" my MUT, even if it's such a small thing (which they obviously even intended because they used the normal Torx screws instead of security Torx screws). I always have the feeling that taking something away could make me regret it in the long run ::)
What are your opinions about this?
-
Personally , I like the belt clip - no way you're gonna loose your MUT . Baout a 50/50 wether I carry it in the pouch , or via the clip .
Chris
-
Meh, why not remove the clip for awhile and see how you like it? You can always pop it back on again later. :)

-
I have wondered if the pocket clip gives the hammer a bit of structural support
so I have been happy to leave my one on
. That said LM made it so you could take it off
. I wonder if anyone has broken a MUT hammer yet
:D :D :D -
@keldan said:
I just don't know what to do with the holes because you can't just put the screws back in as they would stand out too far.
I used the extra screws that came with a set of replacement cutters as blanking screws to protect the threads. Same size and sit flush. All of the removable screws on the MUT are interchangeable.
-
Oh, that's very good to know :)
Thanks, bdl931, I'm gonna get me the replacement cutters and try it out
As for the structural support of the hammer - I have wondered that, too, but I think most of the force is transferred and held by the main frame. The belt clip might have a part in this, but only slightly (if even at all).
I have seen a MUT hammer that had the bolt override part (the "point") broken off, but the whole hammer ... well, someone's probably gonna manage to do that :P Haven't seen one of those yet though
-
Am I just blind or are there really no date codes on the Leatherman MUT? ???
I've been staring at my MUT for quite some time now, long enough to make someone else who might have seen me think I was nuts
but I haven't had any success so far.According to an older thread I found on here (Skeletool Date Codes), Skeletools (which share the general layout with the MUT after all) don't have date codes either.
Can anyone confirm or deny this for the MUT?
-
I did the same thing last week ::) ::) :D :D.
Yep I think the MUT shares the Skeletool's no date stamp status :( :( :(. -
Hi, my first post here and I have a plan to get an EOD this month, have a question about molle that come with EOD, can it hold and carry EOD + 42 bit kit + the bit extender inside? Also anybody here ever try molle with wave, how it was fit? My wave sheath is old and need a new one that also can hold and carry WAVE + 42 bit + bit extender inside, so if I can get any review here I will be ordering another molle with the EOD. BTW I lived in Indonesia, so I can save a lot for shipping cost if I ordered both the EOD and additional molle. I have seen the premium leather sheath II review in another thread, it works perfectly like I want but prefer non leather one.
Thank You.
-
I'm in... It's my favorite by far
-
Seen some chatter about the hammer on this tool, and I can tell you that it has been quite useful for things like tapping nails in. I also tapped out a piece of bent steel with it. I have not used it for any major hammering. I think its a common sense thing to decide what's appropriate and what's not. I have seen a demo of it used to pry out a nail and that sort of thing would make me nervous unless it was an emergency. One youtube review shows that the tip of the hammer broke when used in freezing conditions. Its a nice option to have for light work however.
-
Something designed for "light work" should not be put in the hands of soldiers.
BTW, good to see you made it John!
Def
-
I'm sure it would hold up to 95% of everything. I wouldnt give a number that high to any other MT
-
Mut: inside both handles, right in the center. My clip side is dated 11/10 and other side 12/10. Manufacturers often make components at different times before assembly.
Skeletool: i was wrong... Cant find date -
It gets more "character" the more it gets used, but that's what it's for.

-
Ooops... here's the other side

-
the mut looks so good!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login