Evil's Elixir: A liner locked Leatherman Juice project.....
-
That's going to be a class act.Fantastic job.
-
One handed evil goodness in a juice package!!! Will the madness never end!?!
-
The blade is so freakingly awesome
!! I REALLY loved it, but rust will be an issue wouldn't it?? Considering that the blade is D2 and that we're talking about a folding knife the maintenance on this will have to be regular (right ???). Congrats mate I never get tired of reading your posts, take care!! 
-
Ooh lala.... more great stuff sir

-
@Chain Gang said:
That's going to be a class act.Fantastic job.Thank you Chain Gang.....
@82brutus said:
One handed evil goodness in a juice package!!! Will the madness never end!?!It never ends..... ;)
@WWW said:
The blade is so freakingly awesome
!! I REALLY loved it, but rust will be an issue wouldn't it?? Considering that the blade is D2 and that we're talking about a folding knife the maintenance on this will have to be regular (right ???). Congrats mate I never get tired of reading your posts, take care!! 
Actually, for me anyway, it is because of the lack of maintenance needed that I chose D2 for this blade. I am not referring to the cleaning and oiling aspect, but the need to re-sharpen. I have made many other tools out of D2 and they have held up remarkably well. I have found that, unless they are constantly exposed to moisture and left to sit, a light wipedown every so often with a light oil is all they need to stay rust free. This project will end up being one of my everyday beater tools, so I wanted it to have an edge that will really last. While I use and abuse my tools, I take good care of all of them and keep them in good working order with regular cleanings etc. For some projects, I want more corrosion resistance, for others I want better edge rentention and for others I want a balance of both. Anyway, I hope this helps.....
Thanks Nuphoria.....
-
Very smart sir.
Just a question though, doesn't the thumb stud get in the way somewhat with certain cutting jobs? Such as when the full length of the blade is needed... -
Can you post a picture of the blade along side a wave or charge for comparison?
Great work as always Evil!!! -
@Dexter said:
Very smart sir.
Just a question though, doesn't the thumb stud get in the way somewhat with certain cutting jobs? Such as when the full length of the blade is needed...Thank you, and you have a valid question, however, the same question could be asked about any blade with a thumbstud in general. Actually, this thumbstud, as well as the others that I have made similar to this one, have <u>LESS</u> of a chance of snagging than a typical round bolt style thumbstub. It tapers in both width and height, from full thickness at the bolt to very thin at the tip. If you stabbed through something, it would slide right through like a wedge rather than get stopped at the 90 degreee flat surface of a typical round bolt style thumbstud. Hope this helps......
@Threeme2189 said:
Can you post a picture of the blade along side a wave or charge for comparison?
Great work as always Evil!!!Thank you threeme. It is right in between the length of the standard Juice blade and a Wave blade in terms of length. 1/4" longer than the Juice, 1/4" shorter than a Wave. The cutting edge was brought a 1/4" closer to the pivot bolt. This is how the additional 1/2" cutting edge was accomplished. I'll try and post a pic tonight.....
-
Very smart sir.
Just a question though, doesn't the thumb stud get in the way somewhat with certain cutting jobs? Such as when the full length of the blade is needed...Thank you, and you have a valid question, however, the same question could be asked about any blade with a thumbstud in general. Actually, this thumbstud, as well as the others that I have made similar to this one, have <u>LESS</u> of a chance of snagging than a typical round bolt style thumbstub. It tapers in both width and height, from full thickness at the bolt to very thin at the tip. If you stabbed through something, it would slide right through like a wedge rather than get stopped at the 90 degreee flat surface of a typical round bolt style thumbstud. Hope this helps......
Thanks for that explanation. I see what you're saying now. It's not that easy to see on the photo though. Still...fantastic work Evil!
-
You always seem to leave out the best part, the making of the blade. Any chance you could let us in on that process next time? I'm tossing around the idea of better blade steels for my SAKs and I'd like to see how you go about it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
