Show us your fixed blades
-
@Janitor said:
Well thank you gentlemen.I'm a bit surprised though ... I should have thought that members with post counts like your would know better than to be encouraging a n00b to show his toys off. :)
Ok - Here's a (roughly) 8" Santoku with blue stabalized elder burl slabs. When it came, Mrs Janitor wanted to know what I spent on it. She really had some severe problems with the thought of something like a 'simple kitchen knife' costing that much.
That evening, she used it. It only took a single cut for her to have that 'ah-ha!' moment and admit that she sorted out the difference between this and the department store knives. At this point, I would truely be afraid to try and take it from her.

This image (somewhat) shows the convex grind they put on the Barkies -

Pictures are always good

That Santoku is toooo
to use :ahhh -
Well thank you Sparky.
Yes - they did a beautiful job on it, but I'm afraid that it's used virtually every single day. At least every day that we're home.
-
Putting scales on a Cheap (Pakistani) Damascus blade.
I used a plastic IKEA cutting board (2mm thick) for the handles and Superglue :D
I originally intended to use rivets too, since the Blank already had holes , but I have not yet found the right size (2.4mm, but about 1.5cm long), so I may just make some fake, ornamental, inserts for the holes.

Lesson: do not drill holes in the scales unless you have something to fill them up with!
I am thinking whether to cut some of the scale material, so as to show the file work better.

-
Neat project.
On most of the knives with ornamental file work that I've seen, the scales are flush with the edge, just like you have it. Hard to say from the angle of the photo for sure, but to me it looks like it shows up just fine.
-
Lovely pics and that one with blue stabalized elder burl slabs
...love that blue 
-
@dks said:
Putting scales on a Cheap (Pakistani) Damascus blade.
I used a plastic IKEA cutting board (2mm thick) for the handles and Superglue :D
I originally intended to use rivets too, since the Blank already had holes , but I have not yet found the right size (2.4mm, but about 1.5cm long), so I may just make some fake, ornamental, inserts for the holes.

Lesson: do not drill holes in the scales unless you have something to fill them up with!
I am thinking whether to cut some of the scale material, so as to show the file work better.

Using the chopping board is inspired.
looks excellent. -
@Gareth said:
Using the chopping board is inspired.
looks excellent.
I was looking for suitable handle materials for some time. Plastic cutting boards are robust, chemically stable, heat resistant, easily cut and food safe. Most of the ones I had were, however, too thick.
Then I saw these, and their price was also quite low so they could be destroyed without feeling guilty.
IKEA also sells some slightly thicker ones (possibly 3-4 mm) which would be good for thinner blanks.
You could also stack or use two colours in halves of the thinner ones for fancy looking hadles. -




Hard to see in the pics, so here it is:
-
Cold Steel Gurkha Kukri
-
Koster W&SS with kydex
-
Koster EDC prototype with leather
-
Koster Nessmuck (2x) with leather
-
Koster Bushmaster with leather
-
Koster Bushmaster prototype with leather
-
Busse Tankbuster (2x) with sheaths
-
Busse Bushwhacker Mistress with sheath
-
Busse Boney Active Duty (sterile)
-
SAR-3 SE Satin red/black G10
-
SAR-3 SE DC tan canvas with kydex
-
Ontario RTAK, Rat-3, -5, -7 (2x)
-
Bark River micro Canadian
-
GL Drew small fixed blade (3x)
Becker:
-
Kabar BK2 with kydex
-
Kabar BK7
-
Kabar BK9 with micarta
-
Camillus BK9 (2x)
-
Fallkniven F1 with kydex
-
Fallkniven A1
-
Mexican machete circa 1960, sentimental value
-
Gerber Prodigy
-
Ranger (pre-Ontario, made by Justin) RD-9 (2x)
-
Ranger (pre-Ontario, made by Justin) RD-6
-
-
Holy choppers Batman! :o
So, just enough to get by with then eh Noodle? Lovely collection mate.

-
I'm just preparing in case I have to cut something someday.

-
What sort of sheaths have you got there Mr. Noodle?
Are they just standard issue with the various knives?
I've got an ESEE RC-4 with just the kydex sheath; ideally I plan to add the molle backing, etc.


-
ESEE-6 and A-1 head to head!
Carlos


-
Lovely Falkie

-
This is my Schrade 171, that i have ground down the gaurd, and handle on.

-
That looks good Peter

I think we need some more pictures when you get a min please 
-
Hi Sparky thanks for the kind words. I just couldn't use the knife, with the stock gaurd, & handle on it. It sat in the bottom draw for a long time. One day i said F it, & got the angle grinder out. The same day i cut up a Schrade 140 {i will post a pic today}. Part of me feels bad about chopping those 2 knifes up, there are people that collect them. On the positive side both knifes are now in the using draw.
-
This is my Schrade 140

-
Not much of a fixed blade guy, these are the only ones I got.



-
@Peter said:
Hi Sparky thanks for the kind words. I just couldn't use the knife, with the stock gaurd, & handle on it. It sat in the bottom draw for a long time. One day i said F it, & got the angle grinder out. The same day i cut up a Schrade 140 {i will post a pic today}. Part of me feels bad about chopping those 2 knifes up, there are people that collect them. On the positive side both knifes are now in the using draw.You <u>have</u> to do some work on a knife just to make it yours

Also if a knife doesn’t feel comfortable in your hand you will never enjoy using it

:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login