Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Flashlight modders

Scheduled Pinned Locked Moved Flashlight Forum
16 Posts 1 Posters 2.6k Views
  1. Home
  2. Non Tool Forum
  3. Flashlight Forum
  4. Flashlight modders
Flashlight modders
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • mvyrmnd Offline
    mvyrmnd
    Posts: 717
    mvyrmnd Offline
    mvyrmnd
    wrote on last edited by
    #3 Quote Reply

      That board only has an output current of 1.25A. If you use that board and wire the emitters in paralell, you'll be sharing that 1.25A between all the emitters, each will only see ~415mA.

      You could use that board, wire them in series and each emitter would get 1.25A, but you'd need to use 3 RCR123's (the input voltage must be higher than the output voltage. 3 RCR123's will give an input voltage of 12.6V, the output would be 9.9V)

      1 Reply Last reply
      • tattoosteve99 Offline
        tattoosteve99
        Posts: 6,326
        tattoosteve99 Offline
        tattoosteve99
        wrote on last edited by
        #4 Quote Reply

          Ok I changed my mind. Since the triple is a super flood I want more of a spot beam. So this:
          http://www.ledsupply.com/creexml-w280.php

          Is what I want. What is the board I should use for this one?

          1 Reply Last reply
          • Essexman Offline
            Essexman
            Posts: 1,222
            Essexman Offline
            Essexman
            wrote on last edited by
            #5 Quote Reply

              I was going to say this one http://illuminationsupply.com/8xamc7135-28a-selectable-mode-driver-p-45.html?zenid=aac04abc34fe4b2fa1e47883f64b6c4f

              but no, highest input votage is 6V.

              Maybe go to one 18650 to replace the pair of RCR123? Then you coiuld use the above driver.

              1 Reply Last reply
              • tattoosteve99 Offline
                tattoosteve99
                Posts: 6,326
                tattoosteve99 Offline
                tattoosteve99
                wrote on last edited by
                #6 Quote Reply

                  http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                  I believe this will work?

                  1 Reply Last reply
                  • mvyrmnd Offline
                    mvyrmnd
                    Posts: 717
                    mvyrmnd Offline
                    mvyrmnd
                    wrote on last edited by
                    #7 Quote Reply

                      @tattoosteve99 said:
                      http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                      I believe this will work?

                      It should do. You'll get about 900 emitter lumens from that, expect ~700 OTF.

                      1 Reply Last reply
                      • tattoosteve99 Offline
                        tattoosteve99
                        Posts: 6,326
                        tattoosteve99 Offline
                        tattoosteve99
                        wrote on last edited by
                        #8 Quote Reply

                          @mvyrmnd said:

                          @tattoosteve99 said:

                          http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                          I believe this will work?

                          It should do. You'll get about 900 emitter lumens from that, expect ~700 OTF.

                          Will that work for the single or the triple? Both maybe?

                          1 Reply Last reply
                          • mvyrmnd Offline
                            mvyrmnd
                            Posts: 717
                            mvyrmnd Offline
                            mvyrmnd
                            wrote on last edited by
                            #9 Quote Reply

                              It'd work for the single, and the triple if you wired them in parallel. Each emitter would see 933mA.

                              Assuming you were using R5 bin emitters, each emitter would give ~330 lumens, giving you a total of 990 emitter lumens, or about 700 OTF :)

                              You'd have exactly the same brightness. Well not exactly, but you'd not be able to tell with the naked eye.

                              The XM-L would have a hotspot, and be reasonably throwy, the Triple would be all flood.

                              1 Reply Last reply
                              • tattoosteve99 Offline
                                tattoosteve99
                                Posts: 6,326
                                tattoosteve99 Offline
                                tattoosteve99
                                wrote on last edited by
                                #10 Quote Reply

                                  Fantastic! I'll order some supplies and get to it. I need some backups for my backup.

                                  1 Reply Last reply
                                  • Essexman Offline
                                    Essexman
                                    Posts: 1,222
                                    Essexman Offline
                                    Essexman
                                    wrote on last edited by
                                    #11 Quote Reply

                                      @mvyrmnd said:

                                      @tattoosteve99 said:

                                      http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                                      I believe this will work?

                                      It should do. You'll get about 900 emitter lumens from that, expect ~700 OTF.

                                      TAKE NOTE - 25mm diameter ! Will that fit your heatsink?

                                      I'm only saying beacuse I've done the same before!

                                      1 Reply Last reply
                                      • mvyrmnd Offline
                                        mvyrmnd
                                        Posts: 717
                                        mvyrmnd Offline
                                        mvyrmnd
                                        wrote on last edited by
                                        #12 Quote Reply

                                          @Essexman said:

                                          @mvyrmnd said:

                                          @tattoosteve99 said:

                                          http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                                          I believe this will work?

                                          It should do. You'll get about 900 emitter lumens from that, expect ~700 OTF.

                                          TAKE NOTE - 25mm diameter ! Will that fit your heatsink?

                                          I'm only saying beacuse I've done the same before!

                                          I was speaking electronically. I'd assumed he'd already taken physical parameters into account.

                                          1 Reply Last reply
                                          • tattoosteve99 Offline
                                            tattoosteve99
                                            Posts: 6,326
                                            tattoosteve99 Offline
                                            tattoosteve99
                                            wrote on last edited by
                                            #13 Quote Reply

                                              @Essexman said:

                                              @mvyrmnd said:

                                              @tattoosteve99 said:

                                              http://www.dealextreme.com/p/regulated-cv-cc-led-driver-circuit-board-for-cree-mc-e-ssc-p7-emitters-8-4v-max-input-20330

                                              I believe this will work?

                                              It should do. You'll get about 900 emitter lumens from that, expect ~700 OTF.

                                              TAKE NOTE - 25mm diameter ! Will that fit your heatsink?

                                              I'm only saying beacuse I've done the same before!

                                              Oops! Glad you pointed that out. Lol. Yes I have taken size into consideration but didn't notice that until you said that. Thanks!

                                              1 Reply Last reply
                                              • tattoosteve99 Offline
                                                tattoosteve99
                                                Posts: 6,326
                                                tattoosteve99 Offline
                                                tattoosteve99
                                                wrote on last edited by
                                                #14 Quote Reply

                                                  Where do I find a board to fit my light? 16 or 17mm as mentioned above.

                                                  1 Reply Last reply
                                                  • tattoosteve99 Offline
                                                    tattoosteve99
                                                    Posts: 6,326
                                                    tattoosteve99 Offline
                                                    tattoosteve99
                                                    wrote on last edited by
                                                    #15 Quote Reply

                                                      So what I am doing is changing it some. I can't get a driver that will work lime I want it too so I'll just upgrade my existing light to somewhere around 500 to 600 lumens by building a new drop in. I'll post it up when I get it done.

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      1. Home
                                                      2. Non Tool Forum
                                                      3. Flashlight Forum
                                                      4. Flashlight modders
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0