Question for the pros...
-
I think the MP600 is one of the best MT's Gerber do, so I'd be very tempted with the blunt nose version if that's the kind you are after.

-
The swisstool for sure. I dont like gerbers either.
-
Leatherman Crunch!
http://www.leatherman.com/product/Crunch -
@dks said:
Leatherman Crunch!
http://www.leatherman.com/product/Crunch+1

-
Leatherman Crunch!
http://www.leatherman.com/product/Crunch+1

+2!
-
Gerber MP600 Blunt is the only way to go if you are looking for a true blunt nose geometry. The Vic is more tapered and isn't a true blunt but more of a hybrid blunt/needle nose.
The Crunch could do it, if you are looking for locking pliers, but if that were the case, the Gerber Grappler has its charms as well. Both of these however have a taper at the distal end.
If you are looking for a nice blunt with meat at the pinching end, the MP600 is still your best bet.
-
-
Well I'd agree and go with the MP600 blunt nose suggestions
surprisingly the MP600 head on the older model is very slightly bigger than the SOG micro tool clip, both shown here with a Swiss Spirit.
SOG Micro Tool Clip, Swiss Spirit and MP600 older model.

Close up.

Side on.


-
I like the Gerber 600 blunt nose good MT.
The older SOG PowerPlier were blunt nose if you can find one. :D -
@Grant Lamontagne said:
So... My "multi-fu" is a bit rusty as I've been out of the game for a while. I'm looking for info on multis that DO NOT have needlenose pliers, or at least have somewhat short ones.
Good to see you back again Mikey- looking for a birthday gift are you? :D
Def
My Birthday list is already pretty long. I might just have to sneak one more item on there!
I'm really considering the 600, but my previous experiences with Gerber tools are making me a bit hesitant.
Anyone have a pic of the old powerlock with the blunt nose pliers?
-
@Mike Micklea said:
My Birthday list is already pretty long. I might just have to sneak one more item on there!I'm really considering the 600, but my previous experiences with Gerber tools are making me a bit hesitant.
Anyone have a pic of the old powerlock with the blunt nose pliers?
They're shown here Mike.. :)
The great SOG show-off thread -
My Birthday list is already pretty long. I might just have to sneak one more item on there!
I'm really considering the 600, but my previous experiences with Gerber tools are making me a bit hesitant.
Anyone have a pic of the old powerlock with the blunt nose pliers?
They're shown here Mike.. :)
The great SOG show-off threadThanks for this, didn't know SOG did a blunt nose PP, its all learn learn learn here

EDIT. As if by magic SOG Blunt Nose PP


Will also post it in the auction section
-
At one time you had a SOG ToolClip Mike, so I'm guessing you've already ruled it out. The old SOG PowerPlier is a good option. Also good is the Gerber MP600, but I would recommend one of the earlier ones, before they added the carbide inserts (which have been known to shatter)
Current blunt-nose MP600:

Earlier version:

-
@J-sews said:
At one time you had a SOG ToolClip Mike, so I'm guessing you've already ruled it out. The old SOG PowerPlier is a good option. Also good is the Gerber MP600, but I would recommend one of the earlier ones, before they added the carbide inserts (which have been known to shatter)Current blunt-nose MP600:

Earlier version:

Ok, a thought hit me...
Would it be possible to just cut the tips off of a LM Charge?
-
I suppose it makes more sense to cut them off before they break off. That's something I have thought about doing but never have, so if that's the route you go down be sure to let us know how it works out.
I would also like to point out that I know where there's a small stash of replacement Leatherman plier heads in case something goes horribly wrong.
Def
-
i would agree with the people saying LM crunch. its a really nice tool. but a stumpy charge sounds good.
-
At one time you had a SOG ToolClip Mike, so I'm guessing you've already ruled it out. The old SOG PowerPlier is a good option. Also good is the Gerber MP600, but I would recommend one of the earlier ones, before they added the carbide inserts (which have been known to shatter)
Ok, a thought hit me...
Would it be possible to just cut the tips off of a LM Charge?
Great idea
good luck
pics when done 
-
LM Crunch or SOG Micro Tool Clip....... AWESOMENESS!

-
I do own a Crunch, but it's a bit too limited for what I need. I've also had a Toolclip and Micro Toolclip and didn't care for them. I'm seriously considering cutting the Charge AL, mainly because it's got the tools I use the most on it.
Not sure how to cut it though... Might need Bob's help with this one. :D
-
I think if I'd done it I probably would have just locked it in a vise and took a hacksaw to it then use a grinder (or belt/disc sander) to reshape it. A cast metal plier head can't put up too much of a fight, and I don't think there's any heat treat to mess up, except maybe around the cutters, but going slowly should solve that problem.
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login