AAA Flashlight reco please.
-
I agree with all the recommendations as far as reliable, AAA sized lights go. Although I honestly don't think any of them will do a great job doing lighting work, assuming you meant as part of your wedding photography.
Quick run down of the ones mentioned that I know stuff about:
Fenix E01: Great runtime, especially using Energizer lithiums (~13hr of 10 lumen high followed by 10-20hrs of ~1lumen low). Single mode, basically bomb proof. You'd really have to work at it to break one of these. Good value, pricewise.
Fenix E05: Really nice, all flood beam. Single mode, 30 lumens. I think the runtime on energizer lithiums is about 4hrs. Not as bomb-proof as the E01, but still a good value. Kind of short to me, makes it harder to operate one-handed, if that is important to you.
Fenix LD01 (or older L0D): 3 modes. Most recent version mode sequence id med (~30lumens)-low(~3lumens)-high (~70 lumens). Good build quality. New versions are current regulated, so there is no pulse width modulation (PWM) used to make the low modes.* I have the stainless version, which is my current EDC. This is a little more expensive than some other similar 3 mode lights.
ITP A3: Very well priced 3 mode light. IMO, the quality isn't quite at the level of the Fenix LD01, but it is half the price. Uses PWM, but the newest models use a high enough frequency it shouldn't be noticeable. Highly regarded for its price/value. Newest models are L-M-H mode sequence.
Olight i3: Olight (the maker of ITP) is discontinuing the ITP line and has now issued a revised version of the ITP A3 called the i3. Same modes as latest A3 version. Different clip and keychain attachment. Still well priced for the features.
Streamlight microstream: Good build quality (I think the lens is plastic, though). Single mode. I think it is about 30 lumens (but will appear brighter than a light like the E05 because it uses a reflector to focus the beam). Runtime is short for the output, IMO. Only light mentioned that has a clicky tail switch.
Hopefully this helps. If any of what I said is incorrect, let me know.
*PWM basically turns the light on and off at a really high frequency to make the medium and low modes. If a slower frequency is used, it can result in a strobe effect when moving the light. The newest iTP and Olights use a very high frequency that should be undetectable by your eyes. The newest Fenix's use current regulation, not PWM.
-
@gustophersmob said:
Streamlight microstream: Good build quality (I think the lens is plastic, though). Single mode. I think it is about 30 lumens (but will appear brighter than a light like the E05 because it uses a reflector to focus the beam). Runtime is short for the output, IMO. Only light mentioned that has a clicky tail switch.Hopefully this helps. If any of what I said is incorrect, let me know.
Leatherman Serac S1 the OP asked about also has a clicky switch. (I'd like to get the body of the S1 to use it with my whitest E01 head, an E01 clicky
) -
Streamlight microstream: Good build quality (I think the lens is plastic, though). Single mode. I think it is about 30 lumens (but will appear brighter than a light like the E05 because it uses a reflector to focus the beam). Runtime is short for the output, IMO. Only light mentioned that has a clicky tail switch.
Hopefully this helps. If any of what I said is incorrect, let me know.
Leatherman Serac S1 the OP asked about also has a clicky switch. (I'd like to get the body of the S1 to use it with my whitest E01 head, an E01 clicky
)yeah, the serac S1 always struck me pretty much that, but the cost was so much higher I don't think it ever really took off with the flashlight fans. Mating one with a really good E01 head would be excellent.
IIRC you can make yourself a a clicky L0D by putting together a L0D head and a MicroStream body. I always fancied trying that one.
Oh yeah, the Leatherman Monarch 300 I mentioned also has a tail switch, it has however a very tight spot and isn't much of a flood light. Still a very good light thought IMO.

-
Streamlight microstream: Good build quality (I think the lens is plastic, though). Single mode. I think it is about 30 lumens (but will appear brighter than a light like the E05 because it uses a reflector to focus the beam). Runtime is short for the output, IMO. Only light mentioned that has a clicky tail switch.
Hopefully this helps. If any of what I said is incorrect, let me know.
Leatherman Serac S1 the OP asked about also has a clicky switch. (I'd like to get the body of the S1 to use it with my whitest E01 head, an E01 clicky
)Ah, thanks for the clarification, I wasn't familiar with the Serac. It does look to be a very neat light!
Streamlight microstream: Good build quality (I think the lens is plastic, though). Single mode. I think it is about 30 lumens (but will appear brighter than a light like the E05 because it uses a reflector to focus the beam). Runtime is short for the output, IMO. Only light mentioned that has a clicky tail switch.
Hopefully this helps. If any of what I said is incorrect, let me know.
Leatherman Serac S1 the OP asked about also has a clicky switch. (I'd like to get the body of the S1 to use it with my whitest E01 head, an E01 clicky
)yeah, the serac S1 always struck me pretty much that, but the cost was so much higher I don't think it ever really took off with the flashlight fans. Mating one with a really good E01 head would be excellent.
IIRC you can make yourself a a clicky L0D by putting together a L0D head and a MicroStream body. I always fancied trying that one.
Oh yeah, the Leatherman Monarch 300 I mentioned also has a tail switch, it has however a very tight spot and isn't much of a flood light. Still a very good light thought IMO.

Thanks for the info about the Monarch. I'm not familiar with that light either.
The L0D on the streamlight body does look like a handy combination. I wonder if it works witht the newer LD01?

-
I read somewhere that fenix have changed the threads from square to trapezoid, so the interchangeability of heads between newer and older models is less assured. Worth checking up on if that's important for you.
-
@user24 said:
I read somewhere that fenix have changed the threads from square to trapezoid, so the interchangeability of heads between newer and older models is less assured. Worth checking up on if that's important for you.well here is the original thread from CPF and it seems folks have been using LD01 heads successfully.

http://www.candlepowerforums.com/vb/showthread.php?179101-LOD-CE-head-fits-new-Steamlight-Microsteam-body-%28tactical-switch%29/page6 -
My little Maratac AAA rides unnoticed in my Leatherman sheath, love having 80 lumens there, just in case ;)
-
I love mu Ultrafire A3-R5 stainless. It can found for about 17-20 online and has a great, clean white floods beam, strong clip and is bomb proof.

-
H yah, the black cat Osram is pretty awesome too, it's very slim but no clip

-
@Gareth said:
well here is the original thread from CPF and it seems folks have been using LD01 heads successfully.
http://www.candlepowerforums.com/vb/showthread.php?179101-LOD-CE-head-fits-new-Steamlight-Microsteam-body-%28tactical-switch%29/page6oh cool, can't remember what I was thinking of then.. maybe the ld10 as I as reading a lot about that prior to buying one recently

-
The best single AAA I've used so far has been the Preon Revo
-
Wow I just looked up that maratac and it's THIN!!! Thx
Pretty much I'm looking for something for that LM Wave sheath
-
@ketchupgun said:
Wow I just looked up that maratac and it's THIN!!! ThxPretty much I'm looking for something for that LM Wave sheath
I can't think that any of these lights wouldn't fit in the Wave sheath if I'm honest. :)
-
I just like the Maratac because it has a clip for additional security, 80 lumen capable, and it doesn't interfere with the tool being pulled in & out of the sheath. The Serac lights are nice, I have the S2 and S3. The S2 "fits" in the slot on the sheath, but is too big and tends to make tool access complicated.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login