Zoidberg's Brain Surge.
-
*In regard to idea number one. You will indeed need to shave off some material off of the side of the phillips driver if you want to use the longer flat medium driver aside it. Assuming you will still be using Surge handles, here's the part you may not like to hear, I have the long phillips driver installed in mine and there is more involved than just removing the plier stop if you want the phillips driver to fit. The thickness of the spring system to lock the blades, plus that of the phillips driver, won't allow your handles to fully close. You'd have to shave off way too much off of the phillips driver, thus sacrificing strength. You would have to sacrifice losing the springs which in turn leads to another issue. By removing them you will more than likely have a lot of handle play that will need to be dealt with. If you chose to go this route, you would then have to re-rivet the spring for the locking tab and even still you would need to peen it very flat in order for everything to fit right. Anyway, I hope some of this helps.....
~ evil ~*
-
@evil510 said:
In regard to idea number one. You will indeed need to shave off some material off of the side of the phillips driver if you want to use the longer flat medium driver aside it.Yes, noted above. I had trouble choosing between the Large and Medium Screwdrivers. Maybe I should reconsider and go with strength instead of reach as the amount to shave off the Phillips Screwdriver would be very minimal if any right?
Assuming you will still be using Surge handles, here's the part you may not like to hear, I have the long phillips driver installed in mine and there is more involved than just removing the plier stop if you want the phillips driver to fit.
Correct, for idea one I intend to use both of the Surge handles, sorry I didn't make that clear. While it may not be the best news, the timing is great.
The thickness of the spring system to lock the blades, plus that of the phillips driver, won't allow your handles to fully close.
Would you be up to having an educated guess at how big the gap between the handles would be? I never took to the tapered look of the Surge, being wedged open slightly may give it more style. I will have to think about how this would affect using the outside tools...
You'd have to shave off way too much off of the phillips driver, thus sacrificing strength. You would have to sacrifice losing the springs which in turn leads to another issue. By removing them you will more than likely have a lot of handle play that will need to be dealt with. If you chose to go this route, you would then have to re-rivet the spring for the locking tab and even still you would need to peen it very flat in order for everything to fit right.
Oh, I simply thought if the Core didn't use the spring then the Surge could go without as well. With the Core, the bolts are tighter? And because of the outside tools on the Surge, if you tighten the bolts you clamp onto the tools as well? So the issue is floppy handles in the pliers closed position?
Anyway, I hope some of this helps.....
It all helps. You are one smart cookie. Thankyou for saving me time and stress. I'll have a think about handle gaps and tool selection vs effort, shims and rivets.
<u>Phillips Screwdriver vs Large Bit Driver</u>? No need to be shy now people, what do you use?
-
I agree on the bit driver being a uknown , i recently was out and about on my bike and came across a dumped bike ,so i decided to remove a few parts i needed for my old zaskar, ive added a few modded extras for my bit driver so i was trying to remove the bolts on the brakes with my little extra and it was very stiff, i decided to try with the waves pliers and luckily they loosend the bolts up, i was worried the bit driver might exploid :D reason being the bit driver was built for screw drivers and not sockets,
you have some cool ideas and i look forward to seeing the mod when its done

-
I don't baby the large bit driver on my surge, never had a problem though I do realize the frustrating lack of length. Can't say I've used it much as a nut driver either, I'd guess that would be the real test as most screw heads would cam out before busting the bit holder.
-
@zoidberg said:
Yes, noted above. I had trouble choosing between the Large and Medium Screwdrivers. Maybe I should reconsider and go with strength instead of reach as the amount to shave off the Phillips Screwdriver would be very minimal if any right?I opted for the large because A: it serves well for small prying jobs and B: it is larger than any flat in the standard bit kit and C: I have a no.1 phillips and medium flat that stays in the large bit driver. It does sacrifice reach but I am never far from my extended bits.....
Correct, for idea one I intend to use both of the Surge handles, sorry I didn't make that clear. While it may not be the best news, the timing is great.
If I can save you the trouble of any of the obstacles in the way, that is a good thing.....
Would you be up to having an educated guess at how big the gap between the handles would be? I never took to the tapered look of the Surge, being wedged open slightly may give it more style. I will have to think about how this would affect using the outside tools...
To get a better idea for your own eyes, place something underneath the tip of your phillips driver on your core of equal thickness to that of the locking tab spring + blade retention springs of the Surge and then close up your core to see that gap between the handles. If you want exact measurements, I can mic things out later and get back to you.....
Oh, I simply thought if the Core didn't use the spring then the Surge could go without as well. With the Core, the bolts are tighter? And because of the outside tools on the Surge, if you tighten the bolts you clamp onto the tools as well? So the issue is floppy handles in the pliers closed position?
One would think so. The tolerances of handle widths really vary from one tool to the next, even of the very same type if not from the same batch. Correct, tightening up the bolts to cure the handle play is not the solution because in turn the outside opening tools become very difficult to open. With the correct size of shims, you can adjust handle play and have the outside opening tools work perfectly. These are all issues I had to deal with when putting the ST300 plier head on my Surge. Kind of ironic this topic of handle play should come up now. I use to think that I hated the loose handle play, but, what I have to come to realize is that I like to be able to flip it open but what I disliked was that the handles wouldn't stay closed. My recent mod solves this dilemma for both the Wave and the Surge. Anyway, hope this helps.....
-
@evil510 said:
To get a better idea for your own eyes, place something underneath the tip of your phillips driver on your core of equal thickness to that of the locking tab spring + blade retention springs of the Surge and then close up your core to see that gap between the handles.Somehow I managed to get off my butt and jam some gum under the pliers. Not the best method but it did show me what space was where.
A couple days ago while checking a chainsaw for damage I found the Small Bit Driver was a great fit for cleaning out the bar groove. Nice I thought, put it with the Large Bit Driver and sort out the Awl later. Wrong, the pivot area on the inside of the locking tab said no. The Medium Screwdriver and Lanyard Ring from the Core would have the same problem.
-
-
@zoidberg said:
So the Small Bit Driver went to the Core to wait for next time.Onto the Surge.
The pushed out side.
Awl survives for now.
The pushed in side.
Both sides of the story.
And fully closed. Round one done. Who wants to hear my outside Awl plan?
Clearly!
Also, is that an OOOHOTBE! (outside opening one hand open tactical blade exchanger) I am referring to the hole.
-
-
Mwhahaha. Welcome to the dark side!

-
@Metropolicity said:
Mwhahaha. Welcome to the dark side!Thanks. I tried to resist but the urge was too strong.
Narrowed the inside gap just a little, keeps it closed securely.
I would like to think I'll get around to making that outside awl soon too.
-
Noooo! Now I'll never be able to look at my old reliable Surge without thinking "I should mod this like Zoidberg's". ;)
Thanks for the inspiration,
DaveSent from my iPad2 using Tapatalk
-
Damn you all, reading this thread i couldnt help but swap plier heads on my st300 and surge.
Although i'm now left a gap when in the closed position,
is the ~blade lock/keep closed~ spring the only part that needs to be removed to provide a clean fit?
I did abit of a search but didnt find a full guide only snippets.cheers Tom
-
@16VGTIDave said:
Noooo! Now I'll never be able to look at my old reliable Surge without thinking "I should mod this like Zoidberg's". ;)Remember looks are not everything.
IMO, re the cutters on the different plier heads after using the Surge for months and the ST3 for weeks. Both can cut a nail in half, the ST3 will need more hand power to shear/tear through and the Surge will cut through with ease/less effort. Plier heads were tested on both sets of handles with the same results. I found that the Surge handles are more comfy and the ruler markings felt good.
I tend to carry both tools. If the job looks tool abusive I'll use the ST3 head as I can replace the cutters, otherwise I go with the Surge head for less stress on my hands.
@aussie said:
Damn you all, reading this thread i couldnt help but swap plier heads on my st300 and surge.Although i'm now left a gap when in the closed position,
is the ~blade lock/keep closed~ spring the only part that needs to be removed to provide a clean fit?
I did abit of a search but didnt find a full guide only snippets.Ah, the DaveK gap. Yes, removing the spring will provide a clean fit. I pulled up and slightly back and was able to reuse the rivets.
There is more on the handle play that is mentioned above by evil510 over here.Don't forget to post some pictures, club dark side awaits you.
-
Noooo! Now I'll never be able to look at my old reliable Surge without thinking "I should mod this like Zoidberg's". ;)
Remember looks are not everything.
IMO, re the cutters on the different plier heads after using the Surge for months and the ST3 for weeks. Both can cut a nail in half, the ST3 will need more hand power to shear/tear through and the Surge will cut through with ease/less effort. Plier heads were tested on both sets of handles with the same results. I found that the Surge handles are more comfy and the ruler markings felt good.
I tend to carry both tools. If the job looks tool abusive I'll use the ST3 head as I can replace the cutters, otherwise I go with the Surge head for less stress on my hands.
@aussie said:
Damn you all, reading this thread i couldnt help but swap plier heads on my st300 and surge.Although i'm now left a gap when in the closed position,
is the ~blade lock/keep closed~ spring the only part that needs to be removed to provide a clean fit?
I did abit of a search but didnt find a full guide only snippets.Ah, the DaveK gap. Yes, removing the spring will provide a clean fit. I pulled up and slightly back and was able to reuse the rivets.
There is more on the handle play that is mentioned above by evil510 over here.Don't forget to post some pictures, club dark side awaits you.
I forgot to mention that if you take another pair of pliers and squeeze the handle near the pivot point, you can sneak it closer to the size you need for the SLIGHTLY thinner ST3 plier head BEFORE installation. The rest of the gap can be filled with the original bronze washers either from the ST300 or the Surge, i can't remember.
Hack on!
-
Be warned, this post contains tool abuse.
Scroll down at your own risk and remember you can't unsee things.
I have always thought of the Surge as an ugly tool and now, well, mine is.Small Bit Driver is back, traded for the Awl.
Looks normalish enough. Don't say I didn't warn you though.
The Serpenawl Combo Tool?
Yup, looks just as bad from this side too.
What have I done?
Why?
Because I needed a OOOHOTBO. ;)
Okay. So the Small Bit Driver was always going back in, I use it heaps. The Opener was made to fit the Pocket Clip slot but jammed one day and broke while I was trying to get it out. The plan was file the Serrated Blade down to a large Awl but I generally need small holes not large ones. And I do find a few serrations handy sometimes. I may have made the Opener too large and it looks like smurf but it does work well and I'll update if it breaks. All up it took a few hours, a smurf file, a mill file, couple of round files, a vice and a hacksaw that was no help. If I was to do it again, I would use a grinder and dremel etc and just make one awl to rule them all.
-
-
The only way to stop is start another project ;)
Trust me....I know.
-
That looks like a very useful blade now
Good job 
-
:ahhh :ahhh :ahhh. Would make for a interesting warranty claim :P :D :D."I was dressing my grinding wheel with my Surge when this happened" :o :P :D :D
Cool combi tool mate
, you could scare the bottle tops off by just presenting it too a bottle :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


















