154CM Opinion
-
Thinking about upgrading the Wave in my travel "man bag" to a Charge AL. Mostly for aesthetic reasons, just to have something that doesn't look quite so utilitarian when I pull it out.

Anyway I was looking for opinions from those who have been using a 154CM blade regularly. How is it compared to the Wave's 420HC?
Thanks
-
I had used a Kick for about two years and then upgraded to a Skeletool CX about a year ago. The 154CM is clearly superior to the 420HC. It stays sharp longer and it has the same rust resistance. But its a harder steel so if you beat on the edge (guilty) it takes a little time on a stone to get it sharp again. I'm not saying 420HC is a bad steel, I used a Kick and currently use a Supertool 300 and a recently acquired Fuse, all with 420HC and I find no problems with it.
-
I agree with this assessment.
I would say, however, that going to a Charge ALX gives you the addition of the guthook, which is an extremely handy tool. (You do lose the scissors for a second bit driver however).
-
i have and wave and when i first got my skeletool i was very impressed with the 154CM blade. after some time passed and it got a little blunt i found it hard to get it back to factory sharp.
thats not a bad point about the steel its more to do with my sharpening skills. i think the better the steel the more skill it takes to sharpen. i assume this because i can get a SAK blade hair popping sharp and my LM blast blade razor sharp but my skeletool just doesn't seem the same.
i need to get my skills up and then it will be a great blade again.
-
@Mr. Whippy said:
I agree with this assessment.I would say, however, that going to a Charge ALX gives you the addition of the guthook, which is an extremely handy tool. (You do lose the scissors for a second bit driver however).
I don't really need the gut hook in my bag tool, but scissors are a must. I could see where the ALX would be perfect for someone who uses more than one bit regularly. But my main goal is to "upgrade" the Wave with something a little classy looking with the same features.
I have a Skeletool CX, never used the blade much at all, mostly have it for pocket carry when going to a restaurant or out to the bar.
-
I have 2 expanse knives and the Charge ALX. The edge has held up great over various cuts. Hoping my next 154CM addition will be the Benchmade Barrage or Mini Barrage.
-
Never been much into higher priced knifes. Always been a cheap smurf when it comes to blades. And it's not so much about being cheap, but experience has shown that even a $20.00 SAK is more than adequate for just about any task I throw at it (or throw it at, as it were...)
Although the Benchmades do sound appealing.
-
I have several with 420HC,and S30V,but I prefer the 154CM over all of them,it seems to hold an edge better than both of the other ones,just my opinion.

-
S30V is interesting. It will cut & cut & cut some more, but the "hair splitting" edge does not stick around. The S30V I find tough, but I think the 154 CM holds that fine edge better. Could be completely off base but thats what it feels like in hand.
-
That does make sense. Knowing what little I know about powder made metals, I could see where there could be a limit to the thinness of the very edge of a blade. That being said, once the edge conforms to the grain structure of the steel, it would be incredibly durable.
-
I don't have any 154cm MT's but I have a few folders including a LM expanse.
I think it's one of my favourite steels, It just depends if you sharpen blades often or not. 154cm holds an awesome edge but in my experience it needs to be touched up frequently because if it gets too blunt it becomes a pain to get a true edge back.
I have a spyderco sharpmaker and 154cm has always been easy to touch up. I think it's a great steel, and I would like to see it on more MT's.
-
@Flying Dutchman said:
S30V is interesting. It will cut & cut & cut some more, but the "hair splitting" edge does not stick around. The S30V I find tough, but I think the 154 CM holds that fine edge better. Could be completely off base but thats what it feels like in hand.That is true. S30V will hold a cutting edge longer than 154CM, but 154CM will holder a finer edge longer.
-
154CM, or the ATS version, is my favorite for higher end steels. Doesn't chip as easy as S30V and is slightly quicker to sharpen up. Also much easier to reprofile if need be than D2 and doesn't stain like D2 if cosmetics matter to you. Nothing wrong with 420, you'll just need to resharpen more often, but it will take a super fine edge too.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login