And so it begins.... (My adventures into Alox!)
-
Great job Syph007,, very nice on the torx part!! JR
-
are you using the 93mm saw spring for the scissors? ???
-
@Sidhartha said:
are you using the 93mm saw spring for the scissors? ???Nope, it's one from a 93mm alox solo. They work almost perfect just a little tweaking needed.
-
are you using the 93mm saw spring for the scissors? ???
Nope, it's one from a 93mm alox solo. They work almost perfect just a little tweaking needed.
93mm solo spring perhaps?
-
That looks great!

-
Being able to take this apart easily has already come in handy. The way I mounted the scissors, they were rubbing on the knife blade tip.
And of course I used my trusty SAK ratchet to remove the torx screws!

I flipped the scissors around and this works much much better, smooth action and nothing interferes. The nail nick is also perfectly accessible this way.

And I give you... the Urban Pioneer!


Inner parts still need polishing and screws need locktite, but otherwise finished!
-
@bushidomosquito said:
If I may share what I've learned from playing with these pins, I think it's best for the pins to extend into the scales as far as they can. That way all the torque isn't put on those tiny screws. It also helps with assembly as the scales will snap into alignment and stay instead of you having to hold the springs compressed somehow while you get the last screw in place.Oh boy you were right on the money when you said to get the pivots into the scales as far as possible. I redid my mod and drilled each scale hole with a 1/8 bit, then milled the outside down about 1 mm and used the button head screws. Looks way better now and feels really solid, perfect snap on all tools. The way I had it at first without the pivots actually into the scales would have been awful for the long run.
Really really happy with it now, and the urban pioneer is ready for tomorrow's EDC test run.



-
That looks real good, came out NICE!

-
That looks great! I didn't used to pay any attention to Alox stuff. I just liked the red 91mm SAKs and that was it. Now I'm really into the Alox mods and those dang backtool pins have me wanting to do 91 mods by request only. Once I put a Phillips driver in a 93 that was the end of any reason to carry a 91. 93s have a better awl, stronger blade and the ability to easily adapt the only other 91 tools I wanted which is the scissors and pliers. Not to mention that enlarging the holes is a matter of shaving a minuscule .007"!
One more tip to speed up your disassembly,
http://www.progresstool.com/prod_images_blowup/ba-1446-010-b.jpg
Meisinger 2mm bur. Works like an internal pipe cutter,
http://images.lowes.com/product/converted/017197/017197375163lg.jpgI drill only down past the head portion of the rivet, about 2mm deep. Then the bur gets run around the inside bottom of the hole about 3 times on full Dremel speed with a very light touch and the head pops loose. I broke down 7 SAKs in an hour with no damage to any scale.
-
@bushidomosquito said:
That looks great! I didn't used to pay any attention to Alox stuff. I just liked the red 91mm SAKs and that was it. Now I'm really into the Alox mods and those dang backtool pins have me wanting to do 91 mods by request only. Once I put a Phillips driver in a 93 that was the end of any reason to carry a 91. 93s have a better awl, stronger blade and the ability to easily adapt the only other 91 tools I wanted which is the scissors and pliers. Not to mention that enlarging the holes is a matter of shaving a minuscule .007"!One more tip to speed up your disassembly,
http://www.progresstool.com/prod_images_blowup/ba-1446-010-b.jpg
Meisinger 2mm bur. Works like an internal pipe cutter,
http://images.lowes.com/product/converted/017197/017197375163lg.jpgI drill only down past the head portion of the rivet, about 2mm deep. Then the bur gets run around the inside bottom of the hole about 3 times on full Dremel speed with a very light touch and the head pops loose. I broke down 7 SAKs in an hour with no damage to any scale.
I think I even have that first bit you link, I will have to try it.
This site got me hooked on 93 mm... its so much beefier than 91. Every tool is thicker and stronger... combine that with strong 1/8 inch pivots and extra tools and its a clear winner to me.
I dont even own any 91 mm red knives, the only 91 mm i own is a silvertech huntsman. Alox all the way for me.
Oh ya and enlarging 3mm to 1/8 is very easy, barely feels like even drilling. I'm still on my first carbide bit, so I don't know how long it will go for, but so far so good.
-

Hey
stop drooling on me! JROh yea? Take this sucka.
:D -
Sorry, I have to side with Ashley on this one.

Can I be 2nd in line after Ash?

-
Wow, you are really getting some good results on this alox MOD.
Great work! 
-
@stressmaster5000 said:
Wow, you are really getting some good results on this alox MOD.
Great work! 
Thanks! I've been really happy with this as my EDC, and Ive been showing it off at work. I'm still waiting on my next parts order so I can make more. :D
-
Oh man.. here's another great reason for the torx and pivot method... when you put parts on wrong! LOL Anyone spot a problem here?

This one has the smaller torx button heads and I think I like these the best now, closest look to rivets I think.
-
@Syph007 said:
Oh man.. here's another great reason for the torx and pivot method... when you put parts on wrong! LOL Anyone spot a problem here?
This one has the smaller torx button heads and I think I like these the best now, closest look to rivets I think.
lol i did that on my PT last week , tin opener the wrong way round :D
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
