Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

The Smith pocket sharpener

Scheduled Pinned Locked Moved Edged Tools
10 Posts 1 Posters 2.1k Views
  1. Home
  2. Tool Talk
  3. Edged Tools
  4. The Smith pocket sharpener
The Smith pocket sharpener
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Mr. Whippy Offline
    Mr. Whippy
    Posts: 12,208
    Mr. Whippy Offline
    Mr. Whippy
    wrote on last edited by
    Quote Reply

      This little pocket sharpener is available for less than $10 at Lowes (and I assume Home Depot). It seems like a handy little sharpener for a backpack so I picked one up.

      First thing to note are the 2 V sharpeners. One is carbide and is more aggressive, the other is ceramic and is for touch ups.

      Also note the tapered sharpening rod. I thought it would be great for sharpening guthooks like on Leatherman Charge ALX's, Raker Ring tools and serrated edges.

      After using in for a few months these are my observations.

      The carbide side is more aggressive. But not as aggressive as the Spyderco Sharpmaker medium sticks.

      The ceramic V will bring a dull blade back to a useable level of sharpness. However it will never get a blade back to the fine level of sharpness you can obtain with the Sharpmaker.

      The sharpening rod is VERY aggressive. In fact, it's almost too aggressive. Using it on the cutting hooks never got them back to sharp. If a tool had big nicks in it, it would definitely smooth those out.

      High power of the rod:

      Here it is next to the Victorinox rod I use to sharpen cutting hooks:

      In short, it is a good sharpener for on the fly sharpening of a dull blade, but it won't get the results that the Spyderco Sharpmaker gets. The rod is good for fixing damage, but is too coarse to get a fine edge.

      1 Reply Last reply
      • Chain Gang Offline
        Chain Gang
        Posts: 500
        Chain Gang Offline
        Chain Gang
        wrote on last edited by
        #1 Quote Reply

          I have one and agree 100%.It basically gets the blade ready to be sharpened to a finer edge.

          1 Reply Last reply
          • jzmtl Offline
            jzmtl
            Posts: 8,551
            jzmtl Offline
            jzmtl
            wrote on last edited by
            #2 Quote Reply

              I find those sharpeners are great for axe/hatchet. They are soft so dull fast, but can be restored fast too and you don't need a really sharp edge anyway.

              1 Reply Last reply
              • jerseydevil Offline
                jerseydevil
                Admin Team
                Posts: 10,459
                jerseydevil Offline
                jerseydevil
                Admin Team
                wrote on last edited by
                #3 Quote Reply

                  I keep either that one or another Smiths sharpener in the back room of my store. I get a decent working edge if needed, enough to hold me over until I can get home to my stones. They are useful to have, and cheap enough that I have a couple on hand just in case.

                  Merit Badges
                  Discontinued SAK/MT Challenge Traditional Folder Challenge
                  1 Reply Last reply
                  • Mike Offline
                    Mike
                    Posts: 1,660
                    Mike Offline
                    Mike
                    wrote on last edited by
                    #4 Quote Reply

                      Nice little review, thank you.

                      I would like to add, if I may.

                      Steels are used for re-aligning an edge not for sharpening. They also burnish the steel which is basically the act of smearing the texture of the steel from rough to smooth. This does not involve removal of material. This is also the premise behind the carbide "V" sharpener. You are basically smearing it to some degree of sharpness, and re-aligning the edge. This is a fairly crude method, but does have it's applications though I would not consider it a long term sharpening or touch-up solution.

                      The Spyderco ceramic rods actually remove material. That's what you see as grey lines on them after touching up your blades. Those grey lines are what you have to clean once in awhile to unclog the ceramic and restore the ability of the ceramic rods to cut and remove material.

                      Please note, you do need to clean the ceramic "V" regularly because it clogs quite fast due to the small area where the edge touches. One method is with running water, non-waxed dental floss or non-coated string/twine. Just run the non-waxed dental floss or non-coated string/twine through as you would your blade, then rinse with water. Basically you just want to get in there and remove any material that was removed from your edge. Again, that's just one method. You can probably think of many others since you know the concept.

                      Mike

                      1 Reply Last reply
                      • PyroJames Offline
                        PyroJames
                        Posts: 1,571
                        PyroJames Offline
                        PyroJames
                        wrote on last edited by
                        #5 Quote Reply

                          Nice review, whippy. :cheers: I have one of these as well and they're pretty handy for touching up a blade when you're on the go.

                          1 Reply Last reply
                          • Mr. Whippy Offline
                            Mr. Whippy
                            Posts: 12,208
                            Mr. Whippy Offline
                            Mr. Whippy
                            wrote on last edited by
                            #6 Quote Reply

                              @Mike said:
                              Nice little review, thank you.

                              I would like to add, if I may.

                              Steels are used for re-aligning an edge not for sharpening. They also burnish the steel which is basically the act of smearing the texture of the steel from rough to smooth. This does not involve removal of material. This is also the premise behind the carbide "V" sharpener. You are basically smearing it to some degree of sharpness, and re-aligning the edge. This is a fairly crude method, but does have it's applications though I would not consider it a long term sharpening or touch-up solution.

                              The Spyderco ceramic rods actually remove material. That's what you see as grey lines on them after touching up your blades. Those grey lines are what you have to clean once in awhile to unclog the ceramic and restore the ability of the ceramic rods to cut and remove material.

                              Please note, you do need to clean the ceramic "V" regularly because it clogs quite fast due to the small area where the edge touches. One method is with running water, non-waxed dental floss or non-coated string/twine. Just run the non-waxed dental floss or non-coated string/twine through as you would your blade, then rinse with water. Basically you just want to get in there and remove any material that was removed from your edge. Again, that's just one method. You can probably think of many others since you know the concept.

                              Mike

                              Mike,
                              That is some excellent information. I may have heard it before, but I don't think it stuck. I'm going to clean my Sharpmaker stones now. Thanks man! :tu:

                              1 Reply Last reply
                              • Mike Offline
                                Mike
                                Posts: 1,660
                                Mike Offline
                                Mike
                                wrote on last edited by Mike
                                #7 Quote Reply

                                  @Mr. Whippy said:

                                  @Mike said:

                                  Nice little review, thank you.

                                  I would like to add, if I may.

                                  Steels are used for re-aligning an edge not for sharpening. They also burnish the steel which is basically the act of smearing the texture of the steel from rough to smooth. This does not involve removal of material. This is also the premise behind the carbide "V" sharpener. You are basically smearing it to some degree of sharpness, and re-aligning the edge. This is a fairly crude method, but does have it's applications though I would not consider it a long term sharpening or touch-up solution.

                                  The Spyderco ceramic rods actually remove material. That's what you see as grey lines on them after touching up your blades. Those grey lines are what you have to clean once in awhile to unclog the ceramic and restore the ability of the ceramic rods to cut and remove material.

                                  Please note, you do need to clean the ceramic "V" regularly because it clogs quite fast due to the small area where the edge touches. One method is with running water, non-waxed dental floss or non-coated string/twine. Just run the non-waxed dental floss or non-coated string/twine through as you would your blade, then rinse with water. Basically you just want to get in there and remove any material that was removed from your edge. Again, that's just one method. You can probably think of many others since you know the concept.

                                  Mike

                                  Mike,
                                  That is some excellent information. I may have heard it before, but I don't think it stuck. I'm going to clean my Sharpmaker stones now. Thanks man! :tu:

                                  You bet! :cheers:

                                  For the Sharpmaker rods, something like Comet works very well. You can use it by itself or with those little green and yellow 3M scouring pads. If you're in a hurry, just rubbing them down with hot water gets a lot of it off as well.

                                  A dry way to do it is with those soft white erasers, I suppose pink ones would work too LOL! This is a good way if you won't be around water, Comet, or scouring pads.

                                  Mike

                                  1 Reply Last reply
                                  • Mr. Whippy Offline
                                    Mr. Whippy
                                    Posts: 12,208
                                    Mr. Whippy Offline
                                    Mr. Whippy
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @Mike said:

                                      @Mr. Whippy said:

                                      @Mike said:

                                      Nice little review, thank you.

                                      I would like to add, if I may.

                                      Steels are used for re-aligning an edge not for sharpening. They also burnish the steel which is basically the act of smearing the texture of the steel from rough to smooth. This does not involve removal of material. This is also the premise behind the carbide "V" sharpener. You are basically smearing it to some degree of sharpness, and re-aligning the edge. This is a fairly crude method, but does have it's applications though I would not consider it a long term sharpening or touch-up solution.

                                      The Spyderco ceramic rods actually remove material. That's what you see as grey lines on them after touching up your blades. Those grey lines are what you have to clean once in awhile to unclog the ceramic and restore the ability of the ceramic rods to cut and remove material.

                                      Please note, you do need to clean the ceramic "V" regularly because it clogs quite fast due to the small area where the edge touches. One method is with running water, non-waxed dental floss or non-coated string/twine. Just run the non-waxed dental floss or non-coated string/twine through as you would your blade, then rinse with water. Basically you just want to get in there and remove any material that was removed from your edge. Again, that's just one method. You can probably think of many others since you know the concept.

                                      Mike

                                      Mike,
                                      That is some excellent information. I may have heard it before, but I don't think it stuck. I'm going to clean my Sharpmaker stones now. Thanks man! :tu:

                                      You bet! :cheers:

                                      For the Sharpmaker rods, something like Comet works very well. You can use it by itself or with those little green and yellow 3M scouring pads. If you're in a hurry, just rubbing them down with hot water gets a lot of it off as well.

                                      A dry way to do it is with those soft white erasers, I suppose pink ones would work too LOL! This is a good way if you won't be around water, Comet, or scouring pads.

                                      Mike

                                      Just finished washing them and they look brand new! I used a fibrous scrubby pad, soap and hot water and then rinsed in running hot water. Amazing how much stuff had collected on the stones. Thanks again! :cheers:

                                      1 Reply Last reply
                                      • Ashley Offline
                                        Ashley
                                        Posts: 5,241
                                        Ashley Offline
                                        Ashley
                                        wrote on last edited by
                                        #9 Quote Reply

                                          I use the lansky eraser block a lot myself.

                                          ![!BqTvfrg!mk~$(KGrHqUOKjsEub(lm4woBLvM+Yo(pg~~_3.jpg](/assets/uploads/imported_attachments/migrated/31538!BqTvfrg!mk~%24(KGrHqUOKjsEub(lm4woBLvM%2BYo(pg~~_3.jpg)

                                          Merit Badges
                                          MTO Tool
                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. Edged Tools
                                          4. The Smith pocket sharpener
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0