What Did You Use Your Multitool For Today?
-
This is my day off work, so I'll post something about what I did yesterday.
We had a Turkish Airlines Boeing 777 that came in and the locks that keep all the ULD containers with luggage was frozen. I used the blade on my LM skeletool to dig away at the ice and managed to kick free the lock.
My multitool saved an hour long wait for the 100-200 passengers.
-
@sjian said:
This is my day off work, so I'll post something about what I did yesterday.We had a Turkish Airlines Boeing 777 that came in and the locks that keep all the ULD containers with luggage was frozen. I used the blade on my LM skeletool to dig away at the ice and managed to kick free the lock.
My multitool saved an hour long wait for the 100-200 passengers.
very cool mate, 8) and welcome to the forum, why not post up in the newcomers section

-
welcome to the forum sjian.

-
Nice save sjian! Welcome aboard here as well.

-
@sjian said:
This is my day off work, so I'll post something about what I did yesterday.We had a Turkish Airlines Boeing 777 that came in and the locks that keep all the ULD containers with luggage was frozen. I used the blade on my LM skeletool to dig away at the ice and managed to kick free the lock.
My multitool saved an hour long wait for the 100-200 passengers.
That's... Well Sub-Zero cool :D :D :D

Welcome to the forum!
-
I have been doing some repairs at home so I used the awl on a SAK to make a starter hole for a screw on the bottom of a door.
I then tried to use the file on the LM ST300 to file the heads of some screws on the door handles, with little success...
Then I tried the file on the strike plate of a door (softer steel) to make a hole bigger, with some success….. , then got a dremmel style tool and did the job properly...
I also used regular screwdrivers, a portable bench and a belt sander but who cares about these … :D
Now, I went to a shop and there was a coin stuck in the release hole of a trolley... Unfortunately I did not have a pliers tool on me. If I did, I could have gotten half a Euro :( . It pays to be prepared for all...
-
ST300 got the call to replace kitchen ceiling flo lighting..got to bring one jack-of-all-trade high up on ladder:-)
Good to get phillips, wire cutter/stripper/crimper, awl for pilot...
2 shortcomings...wish the phillip's end is magnetised to hold screw in first place...and encountered frame flex on the last final few turn on high resistance...out come ordinary phillip scrwdrvr!.. -
Used my S2 to cut the foil seal off a new bottle of my prescription meds, and pull the stuffing out.
-
Used my Topeak mini ratchet to fix my wife's car seat.
Jeff
-
ive used my sog power lock wire cutters to cut through 1/2 inch to an inch tree branches :D some of them took more than one cut but thats still cool! plus the cut through solid 1/4 inch copper wire!

-
Used the nail file on a Mini Bear Jaws to try and get most of the gunk out of my Deluxe Tinker. It had lost all it's snap, and the innards were that gritty the springs and scales creaked and crunched when trying to use it. It's better now after an hour with tissue, the nail cleaner, the hot tap and copious amounts of WD40, but it's still a long way from clean. Short of an ultrasonic cleaner I don't think it's going to get much better though
-
Just ten minutes ago, fitted a new rear high level brake light using my new but old and battered KF4, great little tool regardless of its well used figure
and yesterday using the same tool removed a faulty washing machine door closed switch and a PC PSU. In about hour from now I will be using the KF4 to refit a new door switch and a new PC PSU :) So quick question, what's the current equivalent to the KF4 
-
Used an ST300 to change some power door wiring today. The plier head shape is just about perfect for pulling Christmas tree fasteners

-
@badwolf said:
Just ten minutes ago, fitted a new rear high level brake light using my new but old and battered KF4, great little tool regardless of its well used figure
and yesterday using the same tool removed a faulty washing machine door closed switch and a PC PSU. In about hour from now I will be using the KF4 to refit a new door switch and a new PC PSU :) So quick question, what's the current equivalent to the KF4 
From what you've described - the customer service line at Currys

Otherwise, there isn't one
-
I was using my blast to cut straps off a large box today and I dropped it, blade open. What do I do? Instinctively I caught it with my hand between the desk and my body. I only received a token cut on my palm, but still, lesson learned!
-
I used the Classic on my keychain to open a package (containing another SAK of course). Afterwards I put it back in my jeans pocket without closing the blade :ahhh
1 minute later I reached for my keys and the Classic sliced open my middle finger :ahhh :ahhh blood all over the place :D
-
Yesterday I used by Bear & Sons Craftsman-rebranded Bear Jaws to install a webcam in a display mount at a well-known office supply store.

-
Used my Wingman to open up and slice a package of Proscuitto wrapped with mozzarella and a package of crackers! Also got a new electric tea kettle.
-
A couple of days ago I used a Gerber suspension to open the clamshell of a Leatherman MUT from Cabelas. :D
-
@valvestem125 said:
A couple of days ago I used a Gerber suspension to open the clamshell of a Leatherman MUT from Cabelas. :DThat tool should thank you for the privilege.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login