Bucktool - What I should know.
-
In the 1999 Buck catalog is the introduction of the 350 MiniBuck Tool. The 350 MiniBuck Tool came out in 350 standard and 350BKB (Black Oxide). The tools on the 350 also remained the same through out the production years. The 350 (both models) has a small needle nose pliers, scissors , drop point knife, Phillips screw driver(flat), tweezers, nail file, bottle opener and used as slotted screw driver), metric and fractional scales, and a lanyard ring. The 350 came with a plastic molded sheath in black or green.
Standard 350 MiniBuck Tool


350BKB MiniBuck Tool


-
An incredibly fine collection there Longbow.
I'm afraid I am insanely jealous.

How many Bucktools do you actually own??
They all look to be brand new - are they??
Which is your favorite? - Whichever it is, I bet it's a B/O version.
Wonderful,
Many thanks for sharing Longbow. -
Thanks tosh.
I am doing this as a "practice" run for a project I have planned for next year. So any one who can add info or has a question about my information please let me know.
I have most of the "Standard BuckTools" but every time I think I am close to getting a sample of all of them a new variation pops up. I have some new in the box and some that are not new but in good condition. It is hard to find all of these new in the box.
As a teaser I will post my favorite BuckTool near the conclusion of this history.
More to come so stand by! :D -
One note I should bring up in the 1999 Buck catalog the Standard 360 had a tool change. One of the Phillips screw drivers was replaced with a lanyard loop.

In 2000 Buck only came out with one new model of 360 it had Advantage Camo coated handles, the model number for this one was 360CM. This 360CM came with a camo sheath.


In 2001 Buck did not change their BuckTool line it still featured the 360, 360CM, 355 and the 350.
Then in the 2002 catalog the BuckTools were gone.
The introduction of the 735 Navigator was in the 2002 catalog.
Buck was working on a prototype tool name the 735 Navigator it was designed by Buck/Peter Whittaker and was going to be produced over seas how ever this tool was never produced and only a few samples were given to Buck Dealers. So these are very rare and almost impossible to find. I had the privilege of looking at one that a friend has . As for the Navigator design I think it most likely would have been a key chain tool as opposed to a working Mutitool.
(I am still looking to buy a Buck Navigator ;) )

-
Longbow
I wasn't expecting that,
The 735 Navigator looks to be typical of Buck's radical approach to design (bearing in mind this was a decade ago) - pity it never went into mass production - what's your own view on that ?
I note that the current multitool from Buck the '731' is now actually manufactured in China, and from what I've read on various sites this has done the company a great deal of damage
It seems most Americans regarded " Buck " as an iconic brand from a pure wholesome american era.
And, by out-sourcing manufacture to China (of all places) has made a laughing stock of the Buck name.To be fair - reports that I've read so far actually commend the build quality but the past reputation of poorly turned out tack from China has left a stigma that I understand is proving very hard to remove.
-
So far I have hit on some highlights of the BuckTool. There is a whole lot more as time goes by I will add to this thread.
Here is my favorite 360 BuckTool it was a gift to the 7 people who had a hand in designing the BuckTool.
It is 1of7 made, it has a Titanium Nitride gold coating and came with a custom made leather sheath.
Mine is signed by CJ Buck CEO of Buck Knives, he was involved in the BuckTool project.



-
Longbow,
There are a very few multitools that have a Holy Grail like aura and that particular BuckTool is that special.
That is in fact my favorite multitool.
Bruce
-
The BuckTool sheaths.
This is some pictures of various BuckTools and their sheaths. I do not have sheaths for all my BuckTools as some are not new in the box. The 360CL (Pocket Clip did not come with a sheath)
To start off with the original BuckTool 360 (no nail nicks).

This the 2nd year (nail nicks) and the sheath changed, it may have changed part way threw the first year. As far as I can tell the standard BuckTool sheaths remained the same for the duration.

BuckTool Sheath Special Projects and Variations.
360CM (Camo)

360BKB (Black Oxide) Standard 360 sheath

360 Harley Davidson Note the Bit holder pouch and Harley Davidson Logo.
I am not sure if these were done by Buck or after market. I will have to find out.

355 BuckLite tool This is the only sheath I have seen for the 355.

350 Mini BuckTool This is a "molded plastic" sheath. It came in two colors black and green.

350BKB MiniBuck Tool (Black Oxide)

Unfortunately I do not have boxes for all my BuckTools. I tried to show a sample of some of the boxes above. Here are some other packaging types.
350MiniBuck tool

355 BuckLite Tool

360 BuckTool (sheath is in back of blister pack).

-
Info and pics like that is exactly what the Multitool Encyclopedia is made for!

My sprunger is tingling!

Def
-
Longbow
thank you for the information. Your bucklite is interesting because the sheath says bucklite. mine does not. I cannot tell from the picture if the sheath is constructed the same as mine.
in these 2 pictures the very last sheath is a hunter branded buck tool electrician. the second to last is a bucklite 355. it is my favorite sheath because instead of being sewn on both sides it raps the fabric around 1 side and its sewn on the other side. It makes the sheath smaller.
-
Another pic

-
Man I do love these "info" threads.
I'll sift through my Buck stuff and see if I have anything to add :) -
I have four BuckLite 355s all have the same sheath. They all have the BuckLite logo and the wrap around sewn on one side style. Buck also used this style of sheath for knives so it is possible that Buck could have used the knife style sheath with a BuckLite to fill an order.
As for your Hunter named sheath and BuckTool, Buck sold 3500 of the 360 BuckTools to a company called Top Brand. The Top Brand resold these tools with a customer name or logo etched on the tool. When Buck sold these 360s to Top Brand one side of the handle did not have the BuckTool logo stamped on it. It does not mention sheaths but your hunter sheath could be one that Top Brands altered.
If your Hunter tool has the name etched on it could you post a picture of it. I would like to see a 360 that was done by Top Brand.
-
Here are a couple pics.

-
Another

-
Another

-
Yes, the snap says buck
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login