So you think that's sharp...
-
@Grant Lamontagne said:
I'm no physicist, but I really don't think that's possible. The only way you could possibly make it work is to use a downward angled cut with a very sharp knife moving very fast, but then that would get back to the tension issue.
This strikes me as one of those Kevon Costner Bodyguard type things, where he demonstrates how sharp the sword is bu dropping a sheer scarf on the blade and it cuts it. Simply does not happen. Anything that could be cut that easily simply would not be strong enough to survive in an open environment on the planet- and remember, thread may not seem like much, but for it's size it's quite sturdy- it has to be, as it's what holds out clothes together.
Paper is also surprisingly resistant, and the test isn't whether or not it can cut paper, but how cleanly. Paper is fibrous- it's tiny strands of wood fiber going in all different directions stacked on top of eachother then heated and bonded together, similar to plywood. When you tear paper you see lots of fibers, but when cut with a nice sharp blade, the edge of the paper should be very clean, and that is where the challenge lies.
Def
That is pretty much my own assumption, Def.
But I'm beginning to suspect the major problem is the bevel angle and wether the build up of steel to the secondary bevel actually creates a drag thus impeding the performance of the cutting edge. I'm thinking along the lines of a filleting knife but even thinner but gradually easing towards a stonger spine.
Basically, I'm going to assume the secret is to do away with the secondary bevel, but to simply hone down the blade to an almost polished state...ouch :ahhh
Knocking that secondary bevel down a bit will keep your knife a nice slicer. That's the premise behind spyderco recommending use of the 30 degree angles every once in awhile. By knocking that shoulder down, it keeps the angle of the edge from becoming too obtuse. Now, you do need a certain amount of steel behind the edge to provide strength and keep the edge from rolling. This is best achieved by trial and error as it depends on the steel and heat treatment.
A very good book on sharpening is The Razor Edge Book of Sharpening by John Juranitch. Bear in mind that it's geared towards the sale of his products, but the principles are sound and easy to understand.
Knife edge grind reference link:
http://zknives.com/knives/articles/knifeedgetypes.shtmlMike
-
I think they mostly just started cutting paper because their arms were bald.
Def
-
That's no excuse, while they still have their legs available:
-
But I agree that cutting general paper is a weak test. However cutting very soft paper is surprisingly a nice test, and not many blades can do it flawless. For instance, try to make one of those paper-cut tests on toilet paper instead: incredible hard.
-
@Carlos said:
But I agree that cutting general paper is a weak test. However cutting very soft paper is surprisingly a nice test, and not many blades can do it flawless. For instance, try to make one of those paper-cut tests on toilet paper instead: incredible hard.I had actually considered the toilet paper test - however, having once attempted to cut the stuff using a stanley blade - experiance now tells me it's almost impossible.
-
VR to knivesandstuff: Slicing Wet Paper Towel
What about a test like that.
-
@OddFuture said:
VR to knivesandstuff: Slicing Wet Paper TowelWhat about a test like that.
Hmm........Is that water on the Blade ??????????
Not entirely convinced that's authentic. Either the tissue was moistened or the blades were lubricated.
I could be wrong, but you can clearly see somethings running off the blade.
-
VR to knivesandstuff: Slicing Wet Paper Towel
What about a test like that.
Hmm........Is that water on the Blade ??????????
Not entirely convinced that's authentic. Either the tissue was moistened or the blades were lubricated.
I could be wrong, but you can clearly see somethings running off the blade.
Yes the paper towel was wet, so when you go to cut it. It want's to tear instead of cut, but if you get a clean cut then it's sharp.
-
VR to knivesandstuff: Slicing Wet Paper Towel
What about a test like that.
Hmm........Is that water on the Blade ??????????
Not entirely convinced that's authentic. Either the tissue was moistened or the blades were lubricated.
I could be wrong, but you can clearly see somethings running off the blade.
Yes the paper towel was wet, so when you go to cut it. It want's to tear instead of cut, but if you get a clean cut then it's sharp.
No denying those blades are sharp..ouch. much sharper than any I own.
But, surely water softens the fibres of the tissue.
Lets see those blades slice through cotten wool or as originally specified a single piece of hanging thread.
-
@tosh said:
I had actually considered the toilet paper test - however, having once attempted to cut the stuff using a stanley blade - experiance now tells me it's almost impossible.I have been able to cut toilet paper -- dry, wet I've never tested -- but the cutting movement has to be slow and I have only two blades capable of that: an actual razor blade (dovo) and a kitchen knife (kai shun damascus santoku).
-
Actually I've retried that just now and the paper ends up a little teared.
I don't have any video facilities but I leave a picture:
The bottom cuts were made by the kitchen knife, the upper cuts by the razor blade. The upper cuts are more clean, but they also have teared the paper a bit.
I don't have a stanley cutter, but have an OLFA one and also tried with it. It just pushed the paper, no cut or even ripping was done.
-
I test my knives by *push cutting paper * (80 whatever units they use, g/cm or something), not shaving paper which is easier and maybe shaving hair if I feel adventurous... This is usually as sharp as knives come when new and this level of sharpness lasts for some time with resonable use (dont cut wire or on ceramic plates.
The problem with these extra sharp edges is their durability. I can spend an extra few hours to get a scary sharp blade but then that extra sharpness will dissapear after the first few cuts, which makes the whole process of achieving that super-sharpness pointless, for me at least.
Shaving toilet tissue is the new craze that started from the usual forums... I think you are supposed to use one ply for testing, dry not wet....
-
Shaving toilet tissue is the new craze that started from the usual forums... I think you are supposed to use one ply for testing, dry not wet....
[/quote]Didn't know that - has anyone yet succeeded??
-
When I read stuff like this, one thing comes to my mind. OCD
Mike
-
@Mike said:
When I read stuff like this, one thing comes to my mind. OCDMike
It depends.. picture this: you are sitting on the toilet, it is quiet, you are pushing away and you realise you will be for some time..you are a knife nut, so you can not/do not want to read, so you pull out your knife, get some toilet paper and slice away.....the time passes and you are happy.....

EDIT: apparently brand matters too
http://www.bladeforums.com/forums/showthread.php/799423-Toilet-Paper-Sharp -
When I read stuff like this, one thing comes to my mind. OCD
Mike
It depends.. picture this: you are sitting on the toilet, it is quiet, you are pushing away and you realise you will be for some time..you are a knife nut, so you can not/do not want to read, so you pull out your knife, get some toilet paper and slice away.....the time passes and you are happy.....

EDIT: apparently brand matters too
http://www.bladeforums.com/forums/showthread.php/799423-Toilet-Paper-Sharp
-
When I read stuff like this, one thing comes to my mind. OCD
Mike
It depends.. picture this: you are sitting on the toilet, it is quiet, you are pushing away and you realise you will be for some time..you are a knife nut, so you can not/do not want to read, so you pull out your knife, get some toilet paper and slice away.....the time passes and you are happy.....

EDIT: apparently brand matters too
http://www.bladeforums.com/forums/showthread.php/799423-Toilet-Paper-Sharp
If it's bad for your butt, it's probably worse for your knife, regardless of how sharp it is...
-
I remember seeing a video on youtube of a german company making some sort of diamond blade, and was impressed by its sharpness, though I can't find that video now.
When you get pass paper cutting sharpness it's mostly a question of bragging rights, since you'll lose that sharpness the first time you cut anything (other than hair or toilet paper). I don't bother with that level of sharpness anymore, not worth the time. A few swipes on sharpmaker white rod then couple more on strop and it's good.
-
I only strive for "usably sharp" too. I don't bother following up on finer stones or stropping normally either. As soon as it's sharp on the stone I'm using ... I stop sharpening

-
@50ft-trad said:
I only strive for "usably sharp" too. I don't bother following up on finer stones or stropping normally either. As soon as it's sharp on the stone I'm using ... I stop sharpening
I'm in the same camp with you 50ft -
However, I'm basically curious as to what is the absolute edge steel can take. there must be a peak before it then begins to break down.
Just how sharp would that peak be?.......Sharp enough to slice through a single thread ??
We know that a honed blade can shave hairs, slice paper etc etc - and it's a relatively easy goal to achieve.
I'm no metallurgist, but would I be correct in assuming "normal" steel blades simply do not have the grain structure to allow the honing of a super fine edge.
Would laminated steel be the better choice?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




