Multitool repair needed...
-
If I had access to the necessary tools, I'd definitely be up for the challenge, but I don't have a power drill to remove the existing bolts, and I'm not sure how I'd then close everything back up once the new can opener was installed...
The arm of the can opener snapped at the edge of 'the loop', it is literally just a rotatable cuff of metal on the pin, with a roughened edge (which I've filed down so as not to cut my hand when using the pliars) It's definitely a case of replacing it, rather than modifying it into anything else :)
-
Well where are you from?
-
I'm in the UK, but happy to ship abroad if need be to get the work done properly :)
-
@TeeJay said:
I'm in the UK, but happy to ship abroad if need be to get the work done properly :)Tim, unless this tool you want repairing is very special in some way to you, the costs are mounting, please consider posting a want ad in the trade section, I'm sure something will come up at a good price and have you seen this here a Leatherman Kick at a very good UK price of £19.98, very good compact and UK legal tool, well worth considering, you can even take it apart and fiddle with it

-
That's good advice from badwolf mate. A kick is a very good tool and at that price cheaper than modding your old one.
Below pick showing size difference between a micra and kick.

There is room inside for at least two other tools which could come from your old one if you wish. -
@badwolf said:
Tim, unless this tool you want repairing is very special in some way to you, the costs are mounting, please consider posting a want ad in the trade section, I'm sure something will come up at a good price and have you seen this here a Leatherman Kick at a very good UK price of £19.98, very good compact and UK legal tool, well worth considering, you can even take it apart and fiddle with it
Thanks for the link, Jeff, I think the Kick is a little too big for my current carry method (jeans watch pocket) but I'll certainly keep it in mind as a future option should I be unable to effect repairs on my multitool
The piece itself is quite important to me as not only my first multitool, but also my first attempts at tool modification, so I don't want to give up on it just yet :D I'm so far looking at about £12 for the donor tool, and then any additional costs. I've also come up with a revised order of the tool layout to maximize group efficiency, just a case of either finding someone to take on the job, or learning more about peening so I can give it a go myself :)@Farmman said:
That's good advice from badwolf mate. A kick is a very good tool and at that price cheaper than modding your old one.
Below pick showing size difference between a micra and kick.

There is room inside for at least two other tools which could come from your old one if you wish.Thanks for the comparison photo
I do think it might be worth considering, but I really would like to try and get my own fixed before considering a replacement :) -
I believe with a little know how here you will be able to accomplish this on your own. We are available here and by pm (me) for extra help if needed.
-
@tattoosteve99 said:
I believe with a little know how here you will be able to accomplish this on your own. We are available here and by pm (me) for extra help if needed.Thanks for the support
I've been doing some reading, and is it simply a case of drilling the ends off the existing pins, and after swapping the tools round, hammering the ends of the new pins to make them spread out and form the closed end? As another option, are there any pins which can be re-opened with screw or hex ends? -
TeeJay,
:pok: Pictures would really us out with helping you Mate
I have a penknife that I dismantled last year if the bits look like they might fit I can send them to you :tu:
I did a little 'Peening' in the thread below if that helps
Start at around reply No24
1955 Prize
I won the runner up prize at the UK Meet (guess the bouncers weight >:D ) Which was kindly donated by Allen via Zed It was a 1955 BAK with a broken back...
Multitool.Org Forum (multitool.ninja)
-
I believe with a little know how here you will be able to accomplish this on your own. We are available here and by pm (me) for extra help if needed.
Thanks for the support
I've been doing some reading, and is it simply a case of drilling the ends off the existing pins, and after swapping the tools round, hammering the ends of the new pins to make them spread out and form the closed end? As another option, are there any pins which can be re-opened with screw or hex ends?I don't know of any metric sized pivot pins, but Im sure they exist. If the rivet is imperial sized then there are a few places that sell pivots. Unfortunately you wouldn't be able to measure the rivet diameter until you take it apart.
-
Just to say, good luck with trying to repair it yourself, well worth attempting, your'll be surprised at the skills you didn't know you had
and on another note, its just amazing that members from all other the world have offered help, advice and suggestions, something this forum constantly does, makes you feel all warm inside
what a great forum this is 
-
@sparky415 said:
TeeJay,:pok: Pictures would really us out with helping you Mate
I have a penknife that I dismantled last year if the bits look like they might fit I can send them to you :tu:
I did a little 'Peening' in the thread below if that helps
Start at around reply No24Thanks for the offer of the part, having seen the can opener you mean, I know it won't be compatible with the frame, but the offer is very much appreciated :tu: :cheers: Here's a pic of the damage, apologies for the poor quality, but the iPhone isn't really made for quality macro work :D

I've found this tool, which, despite having a different shape of can opener, has other identical tools which mine has, so I'm thinking that they may be interchangeable :)
@Syph007 said:
I don't know of any metric sized pivot pins, but Im sure they exist. If the rivet is imperial sized then there are a few places that sell pivots. Unfortunately you wouldn't be able to measure the rivet diameter until you take it apart.This is definitely starting to look like a 'get it done in one hit' project :D
@badwolf said:
Just to say, good luck with trying to repair it yourself, well worth attempting, your'll be surprised at the skills you didn't know you had :tu: and on another note, its just amazing that members from all other the world have offered help, advice and suggestions, something this forum constantly does, makes you feel all warm inside :salute: what a great forum this is :cheers:Thanks for the encouragement, I think it's going to be a good project when I have some spare cash :tu: :cheers:
-
That link was just to show a bit of peening :) I had forgotten about that opener
I was thinking about this one but it looks like its too long and will foul the pliers, and the nail indent is on the wrong side :-
You are welcome to it if you want to try it (I got a feeling that the pivot hole will be too small)
-
@sparky415 said:
That link was just to show a bit of peening :) I had forgotten about that openerI was thinking about this one but it looks like its too long and will foul the pliers, and the nail indent is on the wrong side :-
You are welcome to it if you want to try it (I got a feeling that the pivot hole will be too small)
Thanks for the offer, but I think it will be long enough to foul the pliars... Is the complete tool shown the Stanley multitool I linked to? Even though the thumb nick would be in the inside, as it will be next to a small low-sitting philips headdriver, it should still be accessible, so I'll pick one up when finances allow

-
Yep thats my Stanley multitool, it lives in my car :)
-
@sparky415 said:
Yep thats my Stanley multitool, it lives in my car :)Cool, I see from the photo it has sprung pliars, but from the description online, I couldn't see any mention of a bottle opener, does it have one? I definitely think that it would provide a suitable replacement part for my multitool when funds allow :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login