What Did You Use Your Multitool For Today?
-
@50ft-trad said:
Just as I was finishing, one of them said "Do you want a screwdriver Al?", **I just peered round the door **and smiled. She said "Yeah, I should have known better - I'll get the kettle on!" :D
I imagine that this is the look you gave her:

:D
Trust me, she's seen me looking a lot worse than that over the years

@Mercury said:
Al, I agree about LM and the awl. I am thrilled that the rebar will have one as I need one all the time.Great story!
Cheers Sean, to be honest I'm not super enthralled by the awls they *do *use.
How tricky can it be for a toolmaker to make a useful hardened, sharpened spike? ::) -
@50ft-trad said:
@50ft-trad said:
Just as I was finishing, one of them said "Do you want a screwdriver Al?", **I just peered round the door **and smiled. She said "Yeah, I should have known better - I'll get the kettle on!" :D
I imagine that this is the look you gave her:

:D
Trust me, she's seen me looking a lot worse than that over the years

@Mercury said:
Al, I agree about LM and the awl. I am thrilled that the rebar will have one as I need one all the time.Great story!
Cheers Sean, to be honest I'm not super enthralled by the awls they *do *use.
How tricky can it be for a toolmaker to make a useful hardened, sharpened spike? ::)

-
Used the PT saturday to repair the dvd player

-
Well with bothg the girls of school sick we became archaeologists for the afternoon looking for dino bones :D they had these little plastic picks that was as good as a chocolate fire guard :D so out came the PT,s saw ;) did a much better job, i also used the Hultafor HK as well


-
@Zed said:
Well with bothg the girls of school sick we became archaeologists for the afternoon looking for dino bones :D they had these little plastic picks that was as good as a chocolate fire guard :D so out came the PT,s saw ;) did a much better job, i also used the Hultafor HK as well

The Paratool is awesome

-
Today at work one of our old-school manual tinting machines threw a fit just when we really needed it. The tint cylinders rotate around a central point, and the platform is locked into place by a spring-loaded pin. We turned it on to agitate the colorants, and the damn thing started spinning like crazy! The pin was jammed! Couldn't get a pair of pliers in to free it. My boss tried wanted to get a paint stick into the gap between the two plates to prevent it from spinning but didn't want any splinters from snapping it getting into the mechanism. All I heard was, " I wish we had a saw." Farmer to the rescue! I used the saw for a nice smooth cut, and used the awl to shave down one end of the shim to fit into the gap with a bit of hammering, which the Farmer also excelled at. Right tool at the right place at the right time!


-
Used my blast to replace an exhaust fan in my bathroom. The new fan was bigger and had to accommodate with the saw.
-
Mended 2 Ikea lamps with SwissGrip. It is strange that the two devices at the one time occurred problems with the internal contacts.
-
Used Charge Ti and Soldier '10 to change risers for the blind on livingroom window...
Then used Chapman ratchet and bit to take cooler protection from my car...
-
I was replacing a window in my Uncle's garage and needed my SOG powerlock to get the glazing points out.
Bonus, I found an old furrier knife while doing it, I'll post some picks after it finishes soaking.

-
Yesterday I put up a section of chain link fence to keep the new pooch in the yard. My Swisstool was great for this and being on my belt was there when I needed it.
-
As usual, I used my Leatherman Kick to do my daily chopping of my insulin needles.

-
Used my skeletool to repair the dishwasher basket
-
I went to Walmart to purchase a Pet Taxi so my dog could ride in my new Camry. When I got it home, I noticed it was packaged so that the top was turned upside down and placed in the bottom, and the holes on the sides lined up. The used zip ties to bind them together through the holes and they were so tight that with a knife you would have to cut them from the top, possibly damaging the edge of the carrier during the cut. I pulled out my trusty Charge Tti and used the v-cutter and had them all cut off in about 30 seconds with no damage whatsoever to the carrier edges. Go Charge!!!
-
Great use of the charge gut hook Hammer!
-
LM KF4 to remove and refit a cooker heater element for my niece

-
@edcgear said:
I've used awl on my P4 to drill a hole near bottom of plastic 2lit bottle. There is no water at my current demolition site and I need to wash my hands. So improvised tap. The screw is just to mark the hole, you actualy unscrew lid to depressurize bottle and start water...

Sent from my Android Paranoid
Very well done sir!
-
Busy day today. Saturday usually is. Today My VIC Spirit got a work out too. First I used the "L" wrench with a #2 Phillips to remove & replace the drain cover, on a shower unit, to snake the drain.

Also Used the pliers to tighten a plastic "wing nut" on a new toilet tank-to-bowl bolt.

Also used the blade to cut the rubberized toilet shims after the install was tested.

Also used the "L" wrench to get a little leverage on a 2" Gate Valve.

Okay, not really. I just thought it was funny. -
Just got a tool adapter for my original super tool so I used it to tighten all the handles on my wife's pans and lids. Then I used the opener to pop the top on a bottle of big boy apple cider.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login