Tofty's Custom Brass Torches
-
I just re-read your photo captions from earlier in this thread....you made your own tap?! :o Wowwwwwww.

-
Well here it is, version 2.0, the forth iteration of my brass torch experiment.

(this one ended up taking 22 hours to render)
(this one took less than an hour and a half to render as it doesn't show the lens)It uses a cree XM-L on a 14mm MCPCB passing through a carclo 10003 20mm TIR lens.
The driver is a 3 mode, 2.8A, 8xAMC7135 unit running off either a single CR123, RCR123 or 16340 battery.
The main head has a solid core between the light engine and the driver for improved heat dissipation with the finning further reducing the problem.
The tail contains a forward mcclicky switch which is shielded from accidental operation.
The components that are usually threaded onto the main body are mostly secured with small M2 countersunk screws.If a moderator could change the title of this thread to "Tofty's Custom Brass Torches" i would really appreciate it.
-
that's one heck of an impressive project mate.
Title change done. :) -
Aiiiiii

-
I'd forever have a toothbrush on it between those fins :P
I'm sure it'll be lovely :D
-
@Tofty said:
Well here it is, version 2.0, the forth iteration of my brass torch experiment.It uses a cree XM-L on a 14mm MCPCB passing through a carclo 10003 20mm TIR lens.
The driver is a 3 mode,** 2.8A, 8xAMC7135 unit running off either a single CR123, RCR123 or 16340 battery**.2.8A from a CR123 ?
-
Yeah alright, not with a CR123 then just the rechargeables, and i doubt it will reach 2.8A, it's just the driver i chose. https://illuminationsupply.com/8xamc7135-28a-selectable-mode-driver-p-45.html.
I could of course make an extra middle section to allow it to use two CR123s and run closer to it's maximum but does it need it? i just designed it to look pretty, if light comes out one end then it's a bonus. -
WOW!! :o That rendering is spectacular Toft!
Can't wait to see the real thing in the flesh :) -
In that case here are a few more renders just for you



Unfortunately i can't really start this build until illumination supply get the LEDs and driver boards back in stock, and i also ought to finish my dive torch before starting this one.
-
@Tofty said:
Yeah alright, not with a CR123 then just the rechargeables, and i doubt it will reach 2.8A, it's just the driver i chose. https://illuminationsupply.com/8xamc7135-28a-selectable-mode-driver-p-45.html.
I could of course make an extra middle section to allow it to use two CR123s and run closer to it's maximum but does it need it? i just designed it to look pretty, if light comes out one end then it's a bonus.i've used the exact same driver in maglite mods with and XML. But I was using 3 C cells making 3.6V. Dam bright!
With such high current your runtime will be limited using CR123 size batts. Have you looked at 18650s ? Twice the length of CR123 size, but you would get longer run time.
Lookimg good anyway, love the pics
-
I want to keep the form factor so if after some testing i'm not happy with the performance i will use the 1.4A driver instead.
My Dark Sucks Alpha uses the 2.8A driver with a 18650 cell so i want to try something a little different. -
Let me know if you need any particular size carbide endmills, drills, taps, etc Tofty. :)
-
@Tofty said:
I want to keep the form factor so if after some testing i'm not happy with the performance i will use the 1.4A driver instead.
My Dark Sucks Alpha uses the 2.8A driver with a 18650 cell so i want to try something a little different.Good point, the single CR123 is a reallt nice in the hand form factor.
I love the Dark Sucks Alpha, had one for a week on a passaround. But it is a long body for a 18650. If you were to compare it to a Zebralight 18650 the zebralight looks like an AA light!!
-
Yeah i like the look of the zebralight sc60 and at 40mm shorter than the alpha seems too short to be possible, pity it can't run at full output for more than 5 minutes.
At least you know your holding the alpha and has been proven to be rather robust.Thanks for the offer J-sews, i need to do a drill audit soon as some of them are a bit worn and some of them are completely......well you know, i'll keep your offer in mind.
-
That looks pretty darn cool. What's the reflector going to be made of?
-
Cheers,
I'm going to use a Carclo TIR (total internal reflection) lens.
It isn't a conventional reflector but rather uses it's shape to internally reflect light until it's alligned with the desired direction of output in quite a tight beam.There nice and cheap and i wanted to try something a little different.
-
Forgive my ignorance but would the fact the reflector is plastic work OK on such a high output light? I've no idea what type of plastic it is of course :)
-
The lens is made from UV stabilised Polycarbonate with close to 90% light transmission efficiency. Polycarbonate starts to soften at 150 degrees celsius and start to melt at 300.
The same type of optic is used in the torchlabs triple LED P60 dropins (over 1000 lumens) with no reported lens meltings.The LED is mounted on a 10mm thickness of solid brass that flairs out to the fully finned surface of the head that will give better heat dissipation than most high energy torches iv'e seen.
The driver goes from low to medium to high so that if the maximum LED output is well above 200 lumens most jobs wouldn't require that much light so a lower setting could happily be used.
If i were to use a lower ampage driver the max output and therefore heat buildup would be much lower than that for which problems could possibly arise.The battery will be a single AW IMR 16340 which will run the light at full power for about 10 minutes max.
And the best thing is that the lenses cost $1.50 each so i can experiment wildly and burn out as many as i like without wasting too much money.
-
Toroughly explained... Thanks!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login