Modding a Rebar questions
-
-
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?
-
@nuphoria said:
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?Well, lots of other stuff would fit in the gap, but the Rebar has such a nice tool compliment already, there aren't many Leatherman options left to choose from.

Hmmm, how about a SOG serrated line cutter? (lock notch would have to be widened, not a big deal)

-
Excellent thread Bob..

Now I* really * need to get my hands on a Rebar... :ahhh -
superb walk through Bob.

-
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?
Well, lots of other stuff would fit in the gap, but the Rebar has such a nice tool compliment already, there aren't many Leatherman options left to choose from.

Hmmm, how about a SOG serrated line cutter? (lock notch would have to be widened, not a big deal)
That's still considered to be a knife over here I suspect, but the SOG V-Cutter might work instead... hmm...
You're right that a Rebar has the basics covered well, but I hadn't considered SOG bits. This is why I asked you

-
-
-
@J-sews said:
Hi Eric,
I didn't try it, but the plier heads look to be completely interchangeable. Here is a photo of a Fuse laying on top of a Rebar:
Here are the same two tools, with the plier heads directly in line with each other. The size and shape of each is identical, except for the "jowls" on the Rebar head that serve to reinforce the wire cutter insert pockets:

Pivot diameters and widths are identical:

This only means one thing my friends...the search continues for 2 BO and a stainless Rebar. I haven't seen them in canada yet, but we are always about a month behind.
I WONDER if there will be a problem with the 'jowls' like the Surge/ST300 head swap. You need to remove the blade safety spring locks to accomodate the width of the head. I am anxious to see if these'll work.
thanks Bob.
-
Very helpful thread! I just wanted to comment on the cutout that would be necessary for the scissors. If I understand this correctly, in order for the scissors to sit flush when they are closed, the notch needed in them would have to be made right on the cutting edge of the scissors, because the scissors would be in the fully open position as apposed to the closed position as shown?
Ben
-
-
@turnsouth said:
This is too tempting, I'm going to have to order a Rebar and use the head to try and make a ReCharge.Are there any caveats on Charge disassembly?
Use two bits. Heat the pivot up a bit to loosen the loctite.
The plier pivots are round so need to worry about stripping a flat portion.
-
@J-sews said:
Folding scissors on the Blast, Fuse, Wave 2004, and Charge models are the same. I started off with a Knifeless Fuse, pictured here alongside a Rebar. (Rebar on left, Fuse on right)
That part ticked me off bit. You do know that this is Multitool.org right?


-
He has to clarify for all those
suspension ownersMultitool beginners that may be reading. -
-
@diracismyhero said:
Very helpful thread! I just wanted to comment on the cutout that would be necessary for the scissors. If I understand this correctly, in order for the scissors to sit flush when they are closed, the notch needed in them would have to be made right on the cutting edge of the scissors, because the scissors would be in the fully open position as apposed to the closed position as shown?Ben
Hi Ben,
yes, the scissors are closed in the photo, but the clearance notch would have to be made right where I've indicated with the white circle.

-
Since, when the scissors are folded into the tool, they are in the fully open position, would the necessary clearance notch cut into the cutting edge of the scissor blade?
-
It would appear that the only protrusion above the handle is the nail nick, is there a way to remove what's needed and retain any portion of the nail nick, or would that leave the thumb tab in the way of the pliers?
-

@Mercury said:
It would appear that the only protrusion above the handle is the nail nick, is there a way to remove what's needed and retain any portion of the nail nick, or would that leave the thumb tab in the way of the pliers?You guessed it, the scissor thumb tab would then unfortunately be in the way of the plier jaws, preventing the tool from folding up completely.

-
@MedusaOblongata said:
Since, when the scissors are folded into the tool, they are in the fully open position, would the necessary clearance notch cut into the cutting edge of the scissor blade?Eek!! How did I miss that?!
Good spot Medusa 

Unfortunately, I'm afraid this pretty well kills the idea of modding Fuse/Blast scissors into a Reber.
Now we'll probably have to wait and hope Leatherman makes a special scissor for the Rebar with a longer shank. 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
So what else was it you were wondering about blade substitutions? ???