Cerakote SAK
-
Yes everything but the mag glass. I'm talking to the coater soon and will be doing prototyping. Looks like I might be back soon I hope. If this works put there might be a small run of custom colors :). The cost will not be outrageously high either as I believe everyone should be able to afford what they want.
-
Dont rule out DIY'ing it. All you need is the cerakote, a high velocity sprayer and a toaster oven. Surface prep is 95% of what determines the final product. :D
-
-
I have a theory that the best aluminum coating would be cerakote over HA3 but done right after the distilled water rinse instead of the dying and sealing process. Fresh anodized aluminum is so porous that is soaks up everything that touches it, skin oils, adhesives, dyes. In aerospace they bond aluminum to composites by giving it a bare anodize finish first to lock in that resin to the surface.
If one had some Alox scales HA3ed after they were blasted with the correct Cerakote grit size and applied the Cerakote while the surface was in that super absorbent state I think it would really up the adhesion and performance.
-
Don't forget you have to prep the surface with 100-120 grit alu oxide to make the coating stick. I know you aren't but it's not ALL that simple ;)
-
Also it has to be dipped in a degreaser and then baked before and after its coated. Plus if I remember correctly heat closes the pores on ha3.
-
Pardon my ignorance, but wouldn't coating the springs just crack the coating? I honestly don't know.
I also am not sure about the durability of cerakote... over on CPF several people have reported their cerakoted HDS's have shown some wear under less than extreme use. What make me wonder about the durability of it is that Henry is known for the quality of his work, but I suppose it could be an issue with the coating service he's using, rather than the coating itself.
Regardless, sounds like a cool idea though... seems like it might be cool to do with some Alox scales too.
-
I would imagine it's limited by the substrate just as HAIII is. I put on 55RC HAIII anodize which is great for abrasion resistance, but on impact its still limited by the much softer aluminum underneath. So cerakote alum scales would still be susceptible to that type of impact deformation, at least as far as I understand. As for the springs, thats a good question, and I dont know how much flex it can handle?
-
No problem with flexibility ;)
-
If anyone has any direct questions or wants to know anything about the Cerakote process or what it can and can't do I will be more than happy to lay it out. It seems as though there is a lot of confusion about Cerakote and how it applies and what it is capable of.
While I don't claim to know it all and be a one stop shop for knowledge on the subject of Cerakote I can say that I have been applying it now for over three years and have seen a lot. I follow the guidelines strictly on prep and application and if I don't know the answer I can for sure find out. This is what I do for a living and I would like to think that I am good at my craft. Knowledge is the name of the game and if you want mine I will be more than happy to share it with you all.
-
@jforbush said:
If anyone has any direct questions or wants to know anything about the Cerakote process or what it can and can't do I will be more than happy to lay it out. It seems as though there is a lot of confusion about Cerakote and how it applies and what it is capable of.While I don't claim to know it all and be a one stop shop for knowledge on the subject of Cerakote I can say that I have been applying it now for over three years and have seen a lot. I follow the guidelines strictly on prep and application and if I don't know the answer I can for sure find out. This is what I do for a living and I would like to think that I am good at my craft. Knowledge is the name of the game and if you want mine I will be more than happy to share it with you all.
We need a step by step guide
please
But I will not use it but just for the knowledge
So .. Make it a thread in the mod squad for people intrested -
Since I'll be owning a cerakoted SAK soon ( :D ), I was doing some research, but came up nothing on lubing. I had read on the forum that someone uses his glock, which is cerakoted, without any lubrication.
Will this work on my SAK? No lubing means less dirt and stuff gets stuck in the SAK.
-
oil, grease, lube ect is a great help. I lube all the complete items that I Cerakote just to make the action smoother.
-
Well as to the one I made earlier. The knife is smooth as silk. A drop of oil and you can hardly tell it moves ;).
-
yep....it don't take much! !:)
-
will be interesting to see how tools with moving/more complex parts will look with the coating, e.g. pliers, scissors.
-
I got my Charge TTi coated and it's holding up fine. The pliers and scissors in particular are fine

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login