Sharpening SAK'S with Lansky
-
Amici,
Add me to the club of unsatisfied Lansky users. The time I owned one which was quite a few years ago, I was never a big fan of the results. Also as a southpaw, I found it a tad cumbersome.. Next in my book will be a Spyderco Sharpmaker, since I've heard nothing but great results..Cheers,
Serge -
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..
-
@EddieEnzyme said:
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..I though Vic's grind was 25 Degrees?
I definitely could be wrong though. -
@EddieEnzyme said:
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..I did the initial marker grind test and 25 on the dot.
-
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..
I did the initial marker grind test and 25 on the dot.
Ah well, that's that idea out of the window.
Heh heh!
-
Aha - found it!
From Victorinox.com, care and preservation section:
Sharpening
Re-sharpen using a whetstone at an angle of 15° - 20°. This will result in a cutting angle of 30° - 40°. If sharpening on a grinding wheel, always cool with plenty of water to avoid excessive temperatures.
I knew I wasn't going mental.
-
I just received my lansky delux system and try to sharp a GAK aitor and basically same problem as the first post, could no sharp as good as I would like, I will continue trying but probably need more practice and correct angle, probably a little reprofile...So, I will continue trying/practice
-
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
-
@Aleister said:
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
-
@Frankctz said:
I just received my lansky delux system and try to sharp a GAK aitor and basically same problem as the first post, could no sharp as good as I would like, I will continue trying but probably need more practice and correct angle, probably a little reprofile...So, I will continue trying/practiceDo you use a sharpy along the edge? I find it really does help

-
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
This is what initially attracted me to the Lansky. I just need some more practice I guess.
I marked the edge on a SAK and i'm going to see whats really going on. -
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
I haven't tried a Charge yet but I tried a Juice with not much luck and a couple of days ago a Squirt (black is sharpened, red is never sharpened):

I started sharpening the black Squirt at 30o and I couldn't make it really sharp. Then I tried reprofiling it to 25o and I still couldn't make it really sharp (I think you can "see" my determination on the blade's sharpening
). Then, I manually used a 280 stone at both sides of the blade (default sharpening is on one side only) and after two hits per side, it became really sharp.Now, don't get me wrong, I like the Lansky system, I just haven't figured out yet how to make it work perfectly with some blades.
-
-
This came up on EDCF lately and it came down to practice.
Sharpmaker....Lansky...any system comes down to muscle memory. For me I like the ease of use, although sometimes a pain to clamp.
But I haven't found anything as precise in the same price point Ahemwickededgecough.
I got my 154cm PE leatherman blade mirror finish with nothing more than the diamond set and and extra super sapphire stone. I tried to take a photo of the edge reflecting my Kinetk Gear Ring that I am trying out as my wedding band.

-
I use the Lansky a lot for regular knives, though I also sharpen some curved or small knife or multitool blades (e.g. LM Sc2) freehand.
The trick is to make sure you are gripping the knife at the same point, in the Lansky clamp, every time and use the same angle.
Thus I have suggested a few times that people **take a picture of the ideal set-up ** they use with every knife, once they find it, to remind them of it, for the individual knife, every time.Generally I use **more pressure at the beginning, with the rougher stones ** and use less pressure with the finishing stones.
Make sure you take enough time with the rougher stones, to get the blade reasonably sharp and remove any metal that you do not need, before moving to the smoother stones, as this are not designed for removing a lot of metal quickly.
Originally I did not spend enough time with the rough stones so it was a pain to get asharp edge later, with the smoother stones.I also always, when I finish with a stone size give the blade a quick once over with the stone on the opposite side to the one I was working on to remove any burr, before moving to the next size stone
.
Again, I strive for push-cutting paper and shaving hair, not anything more (e.g. Toilet paper slicing). -
Good point on the pressure. Too much pressure will just distort the edge, and featherlight passes are needed for final sharpening. For those who are struggling to get an edge on using a Lansky, I'd say ...
- Make sure you are acutally removing material right to the edge (sharpy marker) on both sides.
- Ease off the pressure and let the stones do the work or you'll just be bending the edge away from the stone and weakening it. Too much pressure can also cause the blade to rock in the clamp meaning you are no longer working at the edge, but hitting the shoulder of the two bevels (undoing the checks you did in point 1 and changing the new angle too)
- Finish off by stropping or steeling (lightly) if you can to ensure the edge is straight and burr free. Even clamping at the same point you'll still get some (albeit minor)inconsitencies, and a final alignment (no metal removal) will just help the edge point in the right direction.
Finally, if you have chosen a narrow angle, allow the blade to "rest" before stropping/steeling AND do not strop/steel the knife immediately after use. The blade steel may have some "memory" issues and should be allowed a few hours to relax to its natural position. These memory issues can be caused by heat treatment or machining, don't make it worse by grinding your blades unevenly. Always alternate between the two sides and avoid hitting one side heavier than ther other unless it's a major reprofiling job to correct a bad grind by the manufacturer. Wider/sturdier grinds will be affected far less by this
-
-
-
I believe the best use of a sharpening system is to help the user understand the meaning of the feedback he receives while sharpening knives. So when he feels fairly confident, he can entirely switch to manual sharpening and continue improving his skills.
Now, for more kinesthetic people, a sharpening system might not be of much use due to their already increased hand skills. But, for "not so good with hands" people, I feel that a system can help speed up the learning process.
-
I've been practising with my Lansky 3 stone set - have now sharpened a Pioneer, a Spartan (both 25°) and a Skeletool (30°). Fiddly to setup, particularly on the Spartan but seems to give a nice consistent edge. I did the small blade on the Spartan freehand and that seemed to work well too. Will try a Sharpie on the edge next time and get the magnifier out to check the finish.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login