Modding a Rebar questions
-

Awesome answer.
Take it with a grain of salt, like I said it was a discussion over beer, so there was a lot of "You don't know what you're smurfing talking about" going back-and-forth...
Those conversations are the best!!
@Metropolicity said:
I have 2 BO Rebars from Steve.1 to take apart....
1 to keep.
Soon, my dream compact tool will be realized. BO Wave, Rebar head, 154cm blade...
You must do a thread on that one!
-
Just waiting on them from Steve, they shipped on monday
I HOPE it's a direct swap..although my tools are put away for the move across the country.
I'll see about doing a thread but to do it properly takes time :)
-
Well I suppose that's reasonable.
-
How do you line up the tools & those ever-so-thin washers when putting the bolt back in?
I mangled a small washer between the small bit driver and the scissors on my Charge TTi. Thought I had it lined up but then it fell out. So now when I open the scissors the small bit driver clusters out too. :(Had heard of a wooden jig that Leatherman furnished to overseas repair facilities/shops, but I have yet to see what it looks like.
Had pulled an awl from an ST300 and put in my TTi as I hated carrying all that weight just for an awl.
One would figure after all these years Leatherman would have gotten a hint for at least a limited edition Charge model with an awl in it. Maybe they will get it right with Rebar'ish pliers? -
I use a bit of wire to keep everything together & push the fastener into place, you can wiggle the guiding wire about to help the fastener pass through everything



Crappy photos I know. You can use 2 wires too thread everything into place & then hopefully bung the fastener through
wiggling the wire to get everything lined up helps
. Not sure if it will work with a Charge 
-
@Metropolicity said:
Just waiting on them from Steve, they shipped on mondayI HOPE it's a direct swap..although my tools are put away for the move across the country.
I'll see about doing a thread but to do it properly takes time :)
Moving can prove to be quite exciting,hope all goes well and with out a hitch,good luck.

-JS
-
Just waiting on them from Steve, they shipped on monday
I HOPE it's a direct swap..although my tools are put away for the move across the country.
I'll see about doing a thread but to do it properly takes time :)
Moving can prove to be quite exciting,hope all goes well and with out a hitch,good luck.

-JS
Thanks JS! day 5 of packing and cleaning...the endless chores.
I left out my Vic Spirit and LM BO Wave in hopes that if it was a direct swap, I would walk away with an awesome hybrid tool.
-
@J-sews said:
Unfortunately, I'm afraid this pretty well kills the idea of modding Fuse/Blast scissors into a Reber. :'( Now we'll probably have to wait and hope Leatherman makes a special scissor for the Rebar with a longer shank. :-\OK, Chrissy aborted and I've got her set. I've had a good look over it, and I don't think the lock return spring would be the issue. I'm sure the spring would push up against the scissors when opening another tool, but I don't think that would cause any major problem (just push the tools back down again). As the scissors have to go "one tool in" from the side (for example next to the saw) in order to miss the rocker pivots - the bigger problem would be fitting the scissors down the gap between the saw and the plier head. As for the longer shank scissors fixing it, again I'm not sure.
For each increase made at the shank, the movable arm of the scissors must be increased the same to bring the thumb pad back towards the tool. I don't think there's enough space left between where the Blast scissors would come to, and where the side of the tool curls in of the long tool spots, to be able to increase both the tang and the arm to span the rocker pivots. That is of course unless they ended up making the scissor blades even shorter than they already are :-\ It's almost like they've designed it "unscissormodable" on purpose.
And as for recessing the fastener heads, that's just cruel. Half the fun of multitools is being able to take them apart and make the refinements and design tweaks that they should have done in the first place ::) :P :D
I think it could be made knifeless ... though it might not look pretty in the closed position, but the replacement tool could end up being a bit driver rather than scissors ...
saw to serrated blade spot
can opener to saw spot (it will clear the pivot)
remove spacer washer next to Phillips
complete that side with awl and small flat driverfile to plain blade slot
large flat driver to file slot (it will clear the pivot)
Fit bit driver in centre
Fit spacer washer (from other handle) between bit driver and file -
what makes me sad is that if we are having trouble fitting a set of scissors, then the chances of LM coming up with a scissors version seems to be extremely remote. :-\
-
I'd agree with that
-
@Gareth said:
what makes me sad is that if we are having trouble fitting a set of scissors, then the chances of LM coming up with a scissors version seems to be extremely remote. :-\Unless their veer away from their scissor design and make a new scissor design. It's possible but you know how first productions are. That's why editions and MKII's are made.
-
I'd love to see Surge type scissors that could take the place of one of the 4 large "blades."
-
@MedusaOblongata said:
I'd love to see Surge type scissors that could take the place of one of the 4 large "blades."You'd have to make your own or source some, the pivots are too large on Surge scissors. BUT maybe some Gerber ones, their pivots are quite small.
MAYBE even SOG parts? Never used them before.
-
BOOM!
Dropped in like they were hot:
The Black Tide (Ultimate BO Wave)
THEY'RE HERE!!! I woke up this morning and looked in the mailbox. The day had come, my BO Rebars have landed. Literally tearing open the package like it was ...
Multitool.Org Forum (multitool.ninja)
Except for some scissor woes.
I still believe that scissors CAN be fitted into the Rebar, but some work will have to be done.
-
Just for posterity, and for future modders who will certainly use this thread as a guide.
While putting Wave scissors on the far right side of a Rebar (above the lock hinge) is impossible, any other part of the Rebar will fit in this slot just fine. So, the scissors will fit in the slot immediatly next tothe far right slot, and any of the other single slot tools (can opener, blades, saw, file, flat drivers) will fit perfectly on the far right.
-
Hello!
Rebar is great, but I miss some decent scissors. I have no access to Leatherman spares, so maybe somebody know if SOG scissors would fit more or less? Of course I am aware that grinding may be necessary in that case ;)
regards
-
@IvanDrago said:
Hello!Rebar is great, but I miss some decent scissors. I have no access to Leatherman spares, so maybe somebody know if SOG scissors would fit more or less? Of course I am aware that grinding may be necessary in that case ;)
regards
Welcome to the forum

When you have 5 posts you can send a private message to loki-mobile
He has parts for sale here
</post/1325714>
-
Welcome to
Ivan
All what Steve says is spot on
loki-mobile is very great to deal with and very reasonable on his parts and you have to have the minimum 5 posts for PM to work
The wave scissors are a straight drop in and he sells the wrenches even to take them apart 
-
I'm on the fence about adding scissors to my Rebar. Should I buy Wave scissors from loki? Or maybe use scissors from Vic Swiss Card that I can buy for less than 10$ from local seller? The first option is straightforward, but I guess Vic scissors are better, however need lot of work to be adjusted to Rebar.
-
Get the Wave scissors form Loki. I don't think the vic swisscard scissors will be an easy mod at all.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login