poor, poor, PST
-
Looking good Bruce
Good work with the Scotchbrite wheel
-
Thanks Sparky and everyone who has commented. I thought this project was going to take quite awhile but I am over 90% done. Some touch-up remains and the blade needs sharpened but it might be awhile before I dig out the Dremel tool so here is yet another update.
I rinsed the tool with hot water out of the ultrasonic because the vinegar is a acid and while it brightens the tool it also will cause it to rust. So after a quick shot of air here it is:

Other side:



Finally the closed shot:

It's not perfect but not bad. I need to blend around the one rivet on the LEATHERMAN side and some minor clean up remains but it really came out better than I expected. The file is what really surprised me, usually the file requires some work with the Dremel tool and a small wire brush but the file is nearly perfect.
I'm going to spray it with some CRC Marine 5-56 and put it in a clean jar to soak for Leatherman brown prevention.
More when I get around to working on it some more.
Bruce
-
I realized this is a great place to use Christian St. Clair's Nano Oil! I have used it on tools I want to keep so I put a small drop on every pivot and will put it back in the sun.
-
I'm really impressed with the finish on the handle that had been filed Bruce
Nice Job!

-
Great job Bruce.

-
Just read this thread ... you're a magician, Bruce

-
@sparky415 said:
I'm really impressed with the finish on the handle that had been filed BruceNice Job!

The finish is actually easy when you have the exact same Scotchbrite wheel as Leatherman! My wheel needed to be dressed or I would have gotten a more matte finish. But I thought the shiny might look good and it turned out to match the other handles when it was cleaned in the ultrasonic.
I actually had a couple of jars soaking in Marvel Mystery Oil for the past 3 or 4 weeks so I decided to open them up. I found 5 more Japan PST's, a Pocket Survival Tool, 2 PST's, 2 Surges, and 2 blunt nose Gerber 600's. So since I was already dirty....
The one Surge was sold to me cheap for parts because it would not close and the outer tools would not open. I pried all the internal tools open and the Surge closed! The outside opening tools opened easily and other than being dirty they seemed pretty good. I looked closer and it seemed like the internal tools would not go all the way down, looking a little closer and cheating by comparing to a good Surge I realized both handles were assembled backwards. So as soon as I get a chance I will take it apart for a complete rebuild or I have been thinking of a Recharge...maybe one with scissors and a saw/file exchanger...I wonder if the Surge awl will fit in a Charge?
Bruce
-
Wow! Great job
-
Good work!
That PST looked like a NYC train car. -
@Bensasupertool said:
Good work!
That PST looked like a NYC train car.Thanks,
-
That turned out great. Kudos
-
Amazing results :o Without the photos I wouldn't have believed it was the same tool. You've done a really good job.
-
@Bruce909 said:
Thanks to Gareth I have a subject for this thread!I bought a really bad looking PST on ebay last week and it needs a lot of attention to bring it back to...collectors condition. It currently is in trash collector condition let's hope for something better.
Bob and Dunc, if you think this thread might be under a different category please do not hesitate to move it.
First let look at what we have to work with:




Interestingly it seems to be in decent condition other than the rust. The milled awl looks good and the blade is in great shape.
So the first thing that this tool needs is something to stop the rust. So into a penetrating oil dip, the jar that I put the tool in has a mixture of WD-40, PBlaster, Kroil Oil, CRC Marine and who knows what else. I think this one will stay in the dip for a few weeks. I leave the tools in the sun so they get hot and it cools off at night so there is good opportunity for expansion and contraction. The jar has been in the sun for a few hours and I expect it will get a little hotter than the reading shown on my temperature gun.
In the dip:

You don't want to touch the tools after they have been in the sun for more than a minute:

Suggestions on how to clean it up are appreciated. Keep in mind I have a really nice ultrasonic cleaner for the next steps.
More to come.
Bruce
Aw Man!! That poor thing looks totally victimized!!!
-
You totally nailed that cleanup job Bruce :ahhh
So glad it turned out so nice for ya
I was also pleased and shocked how well that grinded side came back to a factory look 
-
I dont know about everyone else but id like to know about the scotch brite wheel set up. Seem like it might be a good thing to add to a tool collection. Any info you feel like sharing would be appreciated.
-
@tattoocharge said:
I dont know about everyone else but id like to know about the scotch brite wheel set up. Seem like it might be a good thing to add to a tool collection. Any info you feel like sharing would be appreciated.+1
-
The wheel I am using is the Scotch-Brite™ Metal Finishing Wheel in 8" diameter 1" width 3" center hole in the 4A CRS at least that's what I think it is. I went to a local industrial hardware store and asked about the Scotch-Brite wheels. I gave him the info about grit I got from Leatherman and the guy said that the wheels had designations like 2S for silicon carbide or 4A for aluminum oxide. He asked me about the color and I told him it was dark pink. He came back with what he said was Maroon and looked and felt like what I needed. It had a 3" hole in the wheel so I needed to buy adapters also which were not cheap. It all mounted nicely to my bench grinder.
The wheels and adapter were pricey, I got 2 wheels and the adapters and the bill was over $ 200.00.
Here is a 3m Metal finishing catalog that shows the wheel on page 9 and shows all the available arbors and styles of wheels. http://multimedia.3m.com/mws/mediawebserver?mwsId=66666UF6EVsSyXTt5xT_4xs6EVtQEVs6EVs6EVs6E666666--&fn=61-5002-8001-3.pdf
I'll take pictures of my bench grinder and the spare wheel if you want?
Bruce
-
Pictures are always good Bruce

-
@sparky415 said:
Pictures are always good Bruce
Indeed, pics would be great. :)
-
Pictures are always good Bruce

Indeed, pics would be great. :)
I'm with these guys..

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login