What did you use your Leatherman for today?
-
Used the awl in the Rebar to dig out an o-ring out of a homogenizers HVA. :D
-
I brought an old high voltage power supply out to the road for garbage pickup and used the Leatherman Wave's wire cutters to snip off the power plug.
-
Used the large screwdriver on the Rebar to open a Stork control panel.
-
Used the skeletool to tighten the mirror on the work truck :D
-
Various LM tool assisted me in getting drunk.

-
My Rebar was used to take apart a harddrive for the magnets.
-
My wingman was used to dismantle a cheap vacuum that my laborers got pieces of carpet stuck in.
-
I used mu Blast to assemble a 3 legged BBQ set.
-
Used my Kick to open the box my Fuse came in.
-
@trouthunter said:
Used my Kick to open the box my Fuse came in.Tim Leatherman's favorite use for a Leatherman... To open another Leatherman!
-
Charge tti to open a black Rebar.
Just want to help keep Tim happy and designing new models for me to buy. :)
-
Used my Rebar to repair some bench's are my wife's Day Care.
-
Used my TTI to shave wood for a fire so I could make s'mores for my nieces.
Sent from my A500 using Tapatalk 2 -
I used my spirit to remove a clamp from the frame of my truck.
-
I used my Kick to help with fixing the topper on my truck. Strong winds last night tore it off twice. I had to to tie it down with rope and bunge cords. It is now in the dump.
-
Used my PST to open the Mailbox. Key broke in the lock
-
Used the surge flathead screwdriver as a dummy key to start a scissor lift.
-
Used my p4 squirt to remove a data sim card from laptop. I just cut my nails. Easy peasy with my pocket tool.
-
I used my Micra to snip open a butcher's packing paper of cod fillets. Those fillets are marinating now for the last 4 minutes (of 30) in lemon juice & salt, then, I'll coat them with olive oil and season with cayenne pepper and cumin.
I also tried (partially successful) to pick something from between my teeth with the hook tip on the nail file.
Damn, I wish Leatherman would figure out how to get toothpicks in their tools. Until that day, I can never really go without a SAK.
-
I changed a couple of old light switches in my mom's house yesterday. This first one was really old; had no snap action to it at all. Bakelite enclosure and actuator. Forgive the poor lighting: the power was off for this job, so the lighting was from a small LED task light, hanging from a peg nearby.
*With the cover plate taken off, here's the guts. Note the fabric/rubber insulation, and the fact that Mom painted over the screws to make sure I lack no challenge. I used the medium flat screwdriver to chisel the paint out of the groove to remove it

The wires were firmly wrapped around the screws. The needlenose on my Surge came to the rescue. Electricians generally don't use needlenose much. A lineman's pliers is their usual choice. I've done this with a scewdriver, but it is a frustrating process:

Using the #2 phillips bit driver to fix the wires under the screws of the new switch:

Phillips again, to attach/ground the switch frame to the junction box. See how the actuator is clear? I splurged for the switches with the neon bulbs inside; a nice feature in a dark room. ;)

Flat head to attach this very pretty switch plate ;)*

I did another one too, but it was a much more recent switch and more of the same. Didn't have time to repair the dining table chair or replace the light socket on a lamp in the basement. Maybe those will be the next installment? :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login