flip out compound leverage pliers
-
I don't think anyone has done it, likely because of patent issues (although the Gerber sliding head patent just expired, which is why Leatherman is gearing up to produce a sliding head tool) and possibly also because of the complexities involved.
I believe it might be possible, but the issue is that there has to be a disconnect somewhere. The head has to be attached to the handles to slide in and out, but then has to be disconnected from the handles in order to move indirectly (exponentially?) with them. While the standard Gerber (and most plier) heads move in parallel with the handles (handles open ten degrees, pliers open ten degrees) the SOG head moves differently, with the handles opening twenty degrees to open the plier head ten degrees. These aren't actual numbers BTW, just used for illustrative purposes. I don't have an angle gauge or protractor handy for actual numbers.
I suppose it could be possible if you had an internal subframe that the head slid on but moved independently of the handles, or you could put the slide mechanism on the sides of the handles that could allow for differential rotation. Either way though you'd be destroying any internal tool space you might otherwise have.
Interesting concept though...
Def
-
The compound leverage gears take up a good chunk of space. As the nose of the pliers already stick out of the MP series from Gerber, it'd be all the more pronounced in a sliding compound design. Your options would be to let them poke out farther, or cannibalize even more interior space, leaving even less space inside for other tools. You could gain more space by making the tool wider (more full-length tool bays beside the pliers on each side) but then you add bulk to the tool.
And for what benefit? Making the tool less functional, IMO.
Could it be done? Probably yes. Should it be done? I don't see the point. All MTs are a trade-off. The compound leverage pliers can already be one-hand deployed, so there's no gain from them sliding as well.
EDIT: Grant, I think it is very nearly a 2-to-1 ratio on the SOG pliers for movement.
-
2-to-1 is what most of the claims are. I'm not certain if SOG officially claims that much or not. I can't recall the documented numbers at the moment, but I thought it was 2:1. Regardless, this was a question about possibility, not results so I figured exact numbers weren't required.
As for the head sticking out more, that's actually not the case. Take a look at a typical SOG Compound Leverage tool (Crosscut used here since I found that pic first):

You see that the plier (or scissor in this case) pivot is further down the handle than the gear pivot, meaning the gears would stick "up" further than the handles on the standard sliding head Gerber type tool. This could eliminate the points of the Geber type needlenose from sticking out the end.
Interesting possibilities here I think. I wish I had access to some metal working facilities to give some of this a shot... >:D
Def
-
In theory, given Gerber's patent on the sliding plier head design has run out, and we now see offerings from other companies (i.e. Leatherman's OHT), SOG could make a sliding plier head compound leverage tool:- if they wanted to, and if it was possible.
Add in removable hard wire cutters, and the kind of plier head design of the rebar, and you have a beast of a tool.
-
Add in removable hard wire cutters, and the kind of plier head design of the rebar, and you have a beast of a tool.
But why stop there ? Also add in OHO blades, a diamond file, a hacksaw blade plus outside accessible tools and you are really making progress

Sarcasm aside; that stuff comes later.
I'm just pondering about the plier head.
-
sog made a switch plier a while back
-
A very interesting tool, and while the flick action may replace the flick out of sliding plier heads, there isn't any compound leverage.
-
I always thought the switch pliers were compound leverage? They look like it from pictures, but I dont have one to confirm.
-
@Grant Lamontagne said:
I don't think anyone has done it, likely because of patent issues (although the Gerber sliding head patent just expired, which is why Leatherman is gearing up to produce a sliding head tool) and possibly also because of the complexities involved.I believe it might be possible, but the issue is that there has to be a disconnect somewhere. The head has to be attached to the handles to slide in and out, but then has to be disconnected from the handles in order to move indirectly (exponentially?) with them. While the standard Gerber (and most plier) heads move in parallel with the handles (handles open ten degrees, pliers open ten degrees) the SOG head moves differently, with the handles opening twenty degrees to open the plier head ten degrees. These aren't actual numbers BTW, just used for illustrative purposes. I don't have an angle gauge or protractor handy for actual numbers.
I suppose it could be possible if you had an internal subframe that the head slid on but moved independently of the handles, or you could put the slide mechanism on the sides of the handles that could allow for differential rotation. Either way though you'd be destroying any internal tool space you might otherwise have.
Interesting concept though...
Def
You are right, it certainly is a Patent Issue !
It turns out this concept is already present in the original 1998 SOG PatentAnd since the Sliding Method is different from Gerber's, technically they could have done it decades ago.. :o
-
OMGOMGOMGOMGOMGOMGOMGOMGOMGOMG :ahhh :ahhh :ahhh :ahhh :ahhh :ahhh
Why haven't SOG made this?!
-

I don't understand, why am I the only person excited about this discovery?
Or is this old news?
-
That is actually a really interesting design. I think it would be slightly weaker than the Gerber design though, as you are taking away material on the 'sides' rather than the 'top'. It also would probably leave less room inside for tools, although it is only on one side of the tool... hmmm... I actually want to see what one of these would be like in the flesh!
-
Ya the stress point at the top of the slide would be significant. If they ever made a prototype of it, I bet that was the reason to not make a production model.
-
@Roadie said:
That is actually a really interesting design. I think it would be slightly weaker than the Gerber design though, as you are taking away material on the 'sides' rather than the 'top'. It also would probably leave less room inside for tools, although it is only on one side of the tool... hmmm... I actually want to see what one of these would be like in the flesh!But with the Gerber Patent already expired they could do it, right ?

That will be one heck of a tool combining One Hand Opening with Compound Leverage Pliers
-
And to really make it special, why not make it the size of a juice?
And a shears version...

-
I wonder, if there was enough support on these forum for a juice sized MT with flip out compound leverage pliers, would SOG be willing to make it? Are we representative enough of the wider MT buying community?
-
no-one interested in this
? -
IMO too much compromise for too little benefit. Compound leverage on a juice size tool I would love. But sliding into the handle has no value to me. Its easy to open sog pliers with one hand anyway, and if you add this big sliding mechanism it wastes space for tools.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login