Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

first time poster, first mod -- Charge XTi + Rebar

Scheduled Pinned Locked Moved The Mod Squad
28 Posts 1 Posters 11.7k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • B
    B
    Breezy12
    wrote on last edited by
    #1

    I have been a Leatherman owner/fan for 15+ years, and have been collecting them for the past 3-4 years. I recently discovered Metropolicity's Black Tide thread (/topic/37770). Not only did it inspire me to try my first mod after collecting 50+ Leathermans, it also inspired me to take a few pictures and post the results here. 🙂

    Disclaimer: this mod is nowhere near as impressive as the Black Tide, and I've still got work left to do, but I wanted to share what I've done so far.

    The mod itself is really quite simple -- Metropolicity even mentioned dropping the Rebar plier head into a Charge ALX in his Black Tide thread. The Charge Ti has been my favorite Leatherman since I got it in 2004, and it was my EDC for years, so I decided to use a Charge XTi for this mod. I was able to find one in good shape on ebay fairly quickly, then headed down to the Leatherman retail store to pick up another Rebar and a MOLLE sheath for the tool I was trying to create.

    I was ready to start working on the mod, but with my limited equipment, it turned out to be more difficult than I thought it would be. I used a couple C-clamps, a Zippo lighter (to heat the Rebar screws), the security Torx drivers, and a couple other Leathermans to do this. when I took this shot, I had one side of the Rebar removed from the plier head and was working on getting the other side removed.

    The Charge was much easier to take apart (no surprise there), and finally, I was ready to attach the plier head to the Charge. This part was also tougher than I anticipated, but once I had one side attached, the second one was much easier. And the finished product sure looks nice. 🙂

    I have been using the tool as my EDC for about a week now, and I was able to give it a good workout while camping last weekend. one of the dogs that was with our group managed to break the clasp on the cable that was keeping her tethered. we figured out a way to use the loops on the cable to improvise a solution, but the other half of the broken metal clasp was in the way. someone thought we needed a hacksaw, but I had other ideas with my newly modded Leatherman. the 154CM cutters of the Rebar pliers sliced through this clasp like butter -- it took very little effort on my part, and there's not even a scratch on the replaceable cutters.

    That being said, I don't think I'm finished with this tool yet. There is an issue with the locking pin that prevents the serrated blade from opening when the tool is open -- the serrated blade only opens properly if I loosen the Torx screw at the pivot joint by about a quarter turn. The main blade works perfectly, so I'm not sure what the difference is, but needless to say, I'd like to keep tinkering with it until I can get it fixed. I'd also like to replace one of the large bit drivers with other tools (perhaps a large flat driver from a Wave and the awl from the Rebar -- don't think my skills are quite up to the challenge presented by the scissors!), but I'll need to pick up a Wave that can be sacrificed for that purpose first.

    I'd love to hear any ideas/suggestions/comments, but remember, it's my first time -- be gentle. 😉

    IMG_9620_small.jpg

    IMG_9623_small.jpg

    IMG_9627_small.jpg

    IMG_2703_small.JPG

    1 Reply Last reply
    0
    • AHBA
      AHBA
      AHB
      Admin Team
      wrote on last edited by
      #2

      Impressive first post mate.. 😮 :tu: :tu:
      Good to have you here Breezy and we would love to see some pics of your collection.. :pok: 😄

      1 Reply Last reply
      0
      • F
        F
        Farmman
        wrote on last edited by
        #3

        I arrive in the states in two days time. Waiting for me (among others) are a charge and a blast awaiting surgery. This will be my first go at modding and I will let you know how I get on.
        Your mod is great and I look forward to hearing how you solved the problems.

        1 Reply Last reply
        0
        • 3
          3
          3in1
          wrote on last edited by
          #4

          That's a nice looking mod there :multi: :tu:

          Welcome to MTO and keep us updated how this works out :cheers:

          Oh, and :drool: :gimme:

          1 Reply Last reply
          0
          • M
            M
            MultiMat
            wrote on last edited by
            #5

            G'day & welcome Breezy 😄 😄

            Nice first post mate :salute: :salute: congrats on your ReCharge 😄 :D.
            Keen to hear how you get along with your pimped Xti & I hope you sort out the the blade issues mate :think: :think:. Top stuff mate 😎

            1 Reply Last reply
            0
            • Jamie_MJ
              Jamie_MJ
              Jamie_M
              wrote on last edited by
              #6

              Nice job on the mod, and welcome. :cheers:

              1 Reply Last reply
              0
              • nuphoriaN
                nuphoriaN
                nuphoria
                Admin Team
                wrote on last edited by
                #7

                Very cool intro! :cheers:

                I love the idea of the Rebar/Charge hybrid - such a good toolset 🙂

                1 Reply Last reply
                0
                • ducttapetechD
                  ducttapetechD
                  ducttapetech
                  wrote on last edited by
                  #8

                  hello and welcome to MTO. Nice mod! :tu:

                  1 Reply Last reply
                  0
                  • B
                    B
                    Breezy12
                    wrote on last edited by
                    #9

                    thanks for the warm welcome, everyone! 🙂 I think I'm overdue for some updated collection pics anyway, so I'll try to get those up soon. and I'll definitely keep this thread going with any updates to my ReCharge. (love that name!) getting the serrated blade issue sorted out is at the top of the list for sure.

                    1 Reply Last reply
                    0
                    • 3
                      3
                      3in1
                      wrote on last edited by
                      #10

                      Breezy, check out this vid with regards the locking pin issue, it might give you some ideas what is happening

                      Leatherman Surge 300

                      Hope it helps :tu:

                      1 Reply Last reply
                      0
                      • GarethG
                        GarethG
                        Gareth
                        Admin Team
                        wrote on last edited by
                        #11

                        Excellent opening thread Breezy, I think you'll fit right in here. :cheers:

                        1 Reply Last reply
                        0
                        • B
                          B
                          Breezy12
                          wrote on last edited by
                          #12

                          @3in1 said:
                          Breezy, check out this vid with regards the locking pin issue, it might give you some ideas what is happening

                          Leatherman Surge 300

                          Hope it helps :tu:

                          thanks, 3in1! :cheers: I thought about filing down the locking pin (or removing them completely like he did in the vid), but it seems unnecessary in my case since the mechanism works perfectly on one side, and only has the issue on the side with the serrated blade. I'm hoping to have some time this weekend to tinker with it some more and see if I can figure it out.

                          1 Reply Last reply
                          0
                          • MetropolicityM
                            MetropolicityM
                            Metropolicity
                            wrote on last edited by
                            #13

                            Great work!

                            I actually run into that over extended pin problem a lot, it's sticks up just enough to snag and get in the way of either blade. What you can do is take apart the plier again and you can push the pin and whole assembly over a bit to close
                            Up the gap between the wish bone.

                            This not only tightens up the grip on te pliers (very minor) but usually frees up the binding blade.

                            I that doesn't work, you can slowly and carefully grind off the pin's height and check often if it's got enough clearance.

                            Glad I got some modding spirits rustling!

                            1 Reply Last reply
                            0
                            • MetropolicityM
                              MetropolicityM
                              Metropolicity
                              wrote on last edited by
                              #14

                              Also!

                              I am totally going to make a ReCharge too!

                              1 Reply Last reply
                              0
                              • B
                                B
                                Breezy12
                                wrote on last edited by
                                #15

                                @Metropolicity said:
                                Great work!

                                I actually run into that over extended pin problem a lot, it's sticks up just enough to snag and get in the way of either blade. What you can do is take apart the plier again and you can push the pin and whole assembly over a bit to close
                                Up the gap between the wish bone.

                                This not only tightens up the grip on te pliers (very minor) but usually frees up the binding blade.

                                I that doesn't work, you can slowly and carefully grind off the pin's height and check often if it's got enough clearance.

                                Glad I got some modding spirits rustling!

                                thanks Metropolicity -- glad to hear it's not just me! 😄 I'll try taking the plier apart again this weekend, and if that doesn't work, I'll probably just grind the pin down, since it's just barely blocking the serrated blade from opening.

                                Can't wait to see your ReCharge... 😉

                                1 Reply Last reply
                                0
                                • CraigC
                                  CraigC
                                  Craig
                                  wrote on last edited by
                                  #16

                                  Great mod.
                                  Welcome aboard :tu:

                                  1 Reply Last reply
                                  0
                                  • WWWW
                                    WWWW
                                    WWW
                                    wrote on last edited by
                                    #17

                                    Awesome mod sir! :tu:

                                    What great way to start at MTO, be very welcome!! :salute:

                                    And I must say that replaceable wire cutters always make an impressive mod!

                                    1 Reply Last reply
                                    0
                                    • H
                                      H
                                      Heinz Doofenshmirtz
                                      wrote on last edited by
                                      #18

                                      @WWW said:
                                      Awesome mod sir! :tu:

                                      What great way to start at MTO, be very welcome!! :salute:

                                      And I must say that replaceable wire cutters always make an impressive mod!

                                      Likewise! :tu:

                                      1 Reply Last reply
                                      0
                                      • B
                                        B
                                        Breezy12
                                        wrote on last edited by
                                        #19

                                        @Breezy12 said:

                                        @Metropolicity said:

                                        Great work!

                                        I actually run into that over extended pin problem a lot, it's sticks up just enough to snag and get in the way of either blade. What you can do is take apart the plier again and you can push the pin and whole assembly over a bit to close
                                        Up the gap between the wish bone.

                                        This not only tightens up the grip on te pliers (very minor) but usually frees up the binding blade.

                                        I that doesn't work, you can slowly and carefully grind off the pin's height and check often if it's got enough clearance.

                                        Glad I got some modding spirits rustling!

                                        thanks Metropolicity -- glad to hear it's not just me! 😄 I'll try taking the plier apart again this weekend, and if that doesn't work, I'll probably just grind the pin down, since it's just barely blocking the serrated blade from opening.

                                        Can't wait to see your ReCharge... 😉

                                        finally got around to taking the plier apart again to push the pin assembly bit over again... but unfortunately, no luck with solving the issue of the overextending pin. 😕 looks like it's time to start carefully grinding/filing that guy down.

                                        interesting side note: the two handles of the XTi that I started with have different date stamps -- one is 12/04, and the other is 08/08, so this one was obviously refurbished at some point. the pin assembly is just slightly different on the two sides, and the only one having problems is the older side (12/04).

                                        thanks again for the advice, Metropolicity!

                                        1 Reply Last reply
                                        0
                                        • B
                                          B
                                          Breezy12
                                          wrote on last edited by
                                          #20

                                          @Breezy12 said:
                                          interesting side note: the two handles of the XTi that I started with have different date stamps -- one is 12/04, and the other is 08/08, so this one was obviously refurbished at some point. the pin assembly is just slightly different on the two sides, and the only one having problems is the older side (12/04).

                                          ...and a quick check on the Leatherman timeline reveals that these date stamps indicate that the tool I started with was actually half XTi, half TTi, since the TTi production started in 2006. 🙂

                                          1 Reply Last reply
                                          0

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          • Login

                                          • Don't have an account? Register

                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Popular
                                          • World