Kershaw LEEK?
-
I polished my kershaw storm to a mirror finish with dremel, but it was so much pain in the ass I'd never do it again.
-
I was thinking the same thing after doing the Little Bird! :D
Def
-
Def, I have the same gloves with a mini LED light. The Mechanics in yellow though!
-
First post,
I have experience buffing small and difficult parts. Anything with an edge that the buffing wheel can catch on can be dangerous but the fix is easy. just place the knife edge on a flat board and hold it there. If you go over the edge with the wheel it only contacts the board and will not catch on the edge of the knife. This is also the way to polish any thing that has a large hole like a clock bezel which can really grab. You will also need a stick of emory polishing compound to charge the wheel with. Use a soft cotton buffing wheel charged with the emory and keep it moving to keep things even. Do not use a rubber wheel charged with abrasive like Brightboy as it will be impossible to keep things uniform. If the finish is too satin you may have to first sand with wet and dry paper in the finest grades you can find. Use it wet.
Polishing in the flat is a real art and is done quite well on the SAKS, but is very much below the standards set by the watch industry.
Hope this helps,
Richard -
Welcome to the forum Richard! That sounds pretty helpful. Where were you last week when I was doing it to that Little Bird? :D Boy that sounds dirty... :ahhh
LM123- those gloves are the greatest. I wear them fairly often when doing any kind of work where you need to find a better balance between protection and dexterity. I have a few gouges in my fingers from where the wire brush on the Dremel tool slipped and bit me- not enough to draw blood, but removed a few layers of skin and made them pretty tender. I wish I hadn't been so lazy as to decide it wasn't worth the effort to dig them out and wear them! :D
Def
-
@getpower said:
Question two and three (or more of your opinions): Should I get the Leek with the serrated blade, or the straight blade?I just got back into knives last year and asked myself the same question... serrated or plain-edged? I work in a hardware store and need to cut various materials such as rope, tubing, plastics. I've found a plain edge can definitely cut most, if not all, the same materials as a serrated knife. It *might *take one or two cuts more with the plain-edge, but it will do the job. I now buy plain-edged blades.
@getpower said:
Is there any place that sharpens the serration too? Can I send my knife to Kershaw and get the whole thing sharpened once every couple of years? I know that just using a steel rod will hone the knife and that should last a while. But like I said, what about the serration?I don't know if Kershaw does customer resharpening but you can get a sharpener by DMT made for sharpening serrations. It's easy, IMO, but also serrations don't go dull as fast as a plain edge so I wouldn't worry too much about that yet. You can also get something like a Spyderco Sharpmaker that can do serrations and plain edges. Good luck whatever you decide to go with and remember... you can come here when/if feeling guilty about all the $ you will spend on knives.

-
@getpower said:
Question two and three (or more of your opinions): Should I get the Leek with the serrated blade, or the straight blade? Obvious answer would be serrated right! But I am worried about the serration not being able to get sharpened when it gets dull (thats the same issue that I have with my scallion).If you don't have the time/inclination to get a system for sharpening the serrations I would say get the plain edge. Plain edges are also a lot easier to repair if you (accidentally) end up cutting into the dirt while gardening, finding metal wires reinforcing a rubber gasket and so forth.
Unless you work on a boat, it is my understanding that nautical knife use demands a serrated edge.
-
Exactly; for nautical use a serrated edge is invaluable, but for 90% of everything else a plain edge is either perfectly usable or better than serrated. The main appeal of serrated knives for the general public is that they will rip your tomato into mush after 10 years of no sharpening. Of course I prefer my tomatoes to be sliced.
Kershaw does offer sharpening. If you are lucky enough to live in the Portland area, you can drive to the factory in Tualatin and they will sharpen it to you gratis. Kershaw is also known for the good sharp edges they put on their knives. I seem to remember that they are one of the only knife companies that also sharpen serrations for customers for free. Don't quote me on that. I imagine shipping your knives to them involves a $5 handling fee or some such.
-
Maybe you want to try the Eze - Lap 571 t sharpen serrations on a knife, is very easy to use and the price is very affordable
<a href="http://imageshack.us" target="_blank" rel="noopener noreferrer"><img src="http://img177.imageshack.us/img177/8894/571auc3.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Carlos
-
Unless you work on a boat, it is my understanding that nautical knife use demands a serrated edge.
Can help with sawing through some of the tougher lines & bones, but otherwise there's not really any special reason for serrations on a boat.
I get by more or less fine with a plain edge.(though I do have a Serrated Sheepsfoot on board somewhere)
I advocate the Plain Edge for our thread-starter is Plain edge, it's less confusing.
A combo might be alright, but I don't recommend being stuck with only Serrated edges.
-
I have the Kershaw Leek in the rainbow coating! I have about six other Kershaws: Whirlwind, Chive, Steven Seagal knife, Vapor, E.T, rainbow Scallion, and lastly a Blur!
-
I always wanted a rainbow leek! But no local source and I didn't want to pay shipping for just itself.
-
I have a couple leeks (rainbow and the black with gold hardware). They are great knives. Amazing slicers with a very useful blade shape.
My vote is on the plain edge. Serrations are for steak knives (and OHT's!) The leek blade sharpens up so well it scares me.
-
Ok I want to see this rainbow Leek. Can you take a few pics for us LM123? :)
-
I will try to take some on the weekend!
-
@Leatherman123 said:
I will try to take some on the weekend!Great! :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



