DIY Alox
-
That looks cool mate
, how did you go about getting that pattern mate

-
Hehe nice! Your rivet job is really good too!
-
@MultiMat said:
That looks cool mate
, how did you go about getting that pattern mate

I originally wanted to stay with the checkering as on "real" Alox scales, but checkering files cost moonbeams and even a thread file would cost me more than a brand new Farmer...
So, I went with the semi-organic "ripples" look created with a (reasonably) steady hand, a Dremel with variety of burrs, grind stones and polish wheels and then an appointment with the stitched mop on my bench grinder.
But I will be keeping my eyes open for a cheap or 2nd hand thread file. Checkering just looks "The Biz".

-
That looks cool mate
, how did you go about getting that pattern mate

I originally wanted to stay with the checkering as on "real" Alox scales, but checkering files cost moonbeams and even a thread file would cost me more than a brand new Farmer...
So, I went with the semi-organic "ripples" look created with a (reasonably) steady hand, a Dremel with variety of burrs, grind stones and polish wheels and then an appointment with the stitched mop on my bench grinder.
But I will be keeping my eyes open for a cheap or 2nd hand thread file. Checkering just looks "The Biz".

Perfect !

Could you write what type of grind stones and polish wheels you used?
Because i also have a Dremel and you put some ideas in my mind... :D -
Started with a 1/8" round carbide burr to lay down some tracks then a 1/4" stone to widen them out a bit. First blend and polish was with a Cratex rubber point and then bright polish on a stitched cloth wheel on the grinder using white polishing compound.
Hope that is a help.
Also I did some practice on some scrap aluminium to get my hand in first. -
I wanted to try some manual texturing with a checkering file, but they are $60 USD for one. I think though that it would yield some nice checkering. Someday. As long as the checkers dont have sharp ridges on them, the hard anodize I do should look decent.
-
The sharpness of the checkering is controlled by the depth of the cut. Normally you would leave the squares flat-topped unless you want a very aggressive surface. Checkering files clog easily...the trick I picked up is to rub them with blackboard chalk when using them.

-
Hey that looks sweet! Ok I gotta try this now. :D Chalk sounds like a good tip, I have a bag of it from my rock climbing days.
-
Checkering files huh? I'm ordering me some! Nice mods :)
-
I find it useful to look at photos of real ripples for "inspiration"... not that I'm anywhere near reproducing that degree of realism.
some examples...
http://www.danheller.com/images/California/DeathValley/Dunes/sand-ripples-big.jpg
http://upload.wikimedia.org/wikipedia/commons/1/16/Water_Ripples_1.jpg
BUT, I have plenty of scrap aluminium so I'll keep hacking away, striving for that fluid metal look.
-
ok, I sat down with some water pic's and took dremel to some scrap aluminium.
After about an hour of assorted cuttung, grinding, sanding and polishing I got this....and DAMN is it hard to photograph..

-
Nice. I really like that one.
There was a fellow from Australia that used to do melted Alox scales...don't remember his name though.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

