Surge Outside Mounted Bit Holder
-
Good Day!
I wasn't satisfied with keeping the dental pick on the Improviser. I do tend to need picks from time to time, but not often enough to justify an outside mounted tool. I knew that when I made it, but it was such a nice challenge, I did it anyway.
But, I couldn't get past the idea of a outside opening bit holder.
So, I took apart the ''Leftovers” Surge, and stole the bit driver from it.
15 min. of looking, and holding, and measuring clearances, and I decided I needed to at least be able to put it in, on the pivot, to know if it would work. Problem was, that meant enlarging the hole in the driver, and if it didn't work, it would be useless as an inside tool again.
Only took me another 15 min to go “oh well, it IS the parts tool, not like its from my main tool, its expendable” And I started grinding…
Long story short, about an hour later, I had what I started out to do, and it works!
OMBH, and, it opens one handed too, so I guess its a OHOOMBH. ;)Only ''problem'' is, the pivot barrel only goes about half way through the holder. Its good and solid, no play or flex, but a some point it would be a good idea to get or make a longer pivot.
And, I can sill have a pick, just need to thin the hex end of another pick. The welded up pick is now on the Leftovers Surge.


With the longer bit from the MUT tool kit;


Here you can see where I inset the back to clear the upper lip on the handle frame, to allow it to open perfectly straight—inline with the handle. And, the notch made in the 'tang' for the liner lock to catch. Yes, its very narrow, but I can press to close the tool against the lock pretty darned hard; its not gonna close in use.
There was some bending out of the handle frame, to make room for the bit to close into the groove, and also some grinding Inside the groove to clearance for the bit, but only the first inch or so from the holder end, after that the bending out was enough.


You can see here, where the 'tang' isn't wide enough, and drops off of the lock at a kinda 'half stop' where you have to press in the lock again. I mite weld a bit of a tab on the side there, to profile it out so it doesn't do this. Depends on how annoying it gets.

-
Whoa !! :o very interesting mod !!

-
Wow your Surge has had more modifications than Michael Jackson's nose had :o :D
Interesting mod mate , it would be cool if you had a stand alone OHO bit holder that took standard 1/4 inch tool bits

-
cool mod mate thanks for sharing

-
Thanks Gents!
@MultiMat said:
Wow your Surge has had more modifications than Michael Jackson's nose had :o :DInteresting mod mate , it would be cool if you had a stand alone OHO bit holder that took standard 1/4 inch tool bits

Yeah, about the only thing Surge thats left is the handle frames, and even they've been carved up quite a bit now.

Can't be done as far as I can tell... The holder area on a standard 1/4" driver is just too
thick. You can see how thick this holder is, how it sits flush with the frame, and the
bit fills the groove... Can cut out the outer handle frame to clear it like I did here, but
to clear the other side of it you would have to cut into the inner frame side.I guess it could be done, a the right length, to not interfere with the inner tools, or the pliers
head seating, but it'd be close. I'd also worry about structural integrity of the handle.Personally, I prefer the LM bits to full 1/4" hex, I can carry 20 variations in the same
space it takes for 10 regular bits. The wider drivers, like #2 phillips mite slip from time
to time being thinner in one profile, but anything smaller is still cut in full profile and
works fine.G.
-
Another clever and original idea

-
Very nice never would have thought of making an outside but holder. :D
Sent from my LG-P925 using Tapatalk 2
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

