And so it begins.... (My adventures into Alox!)
-
@crackout said:
Amazing!
So you actually made super thick springs that'd fit pliers with minimal thinning and the rest with more? Good idea, yet still a lot of work if you're forced to finish them by hand.In your CAD image, the spring looks thinner than the laser cut outcome though.
Ya it was jut a 2D file that was sent to laser. The material I chose was what determined the thickness. I for sure don't want to be finishing 200 by hand, but a few this way to get some mods done is fine.
Here is an overlay to show how the scissors were made to fit, and what can be removed to fit pliers.

-
Wow that's thin!
How much offset did you do on the center hole for tension build up?
-
The pliers and spring both have to ground to fit. The same as using pliers with 2 saw layer back springs.
I made the curve of the spring exactly the same profile of a stock Vic spring for tension. Heat treat made it curl just a bit more than a stock one, but the the added spring tension just added to the snap. It works very smooth with scissors, and I'll give the pliers a test next.
-
As I know one of these backsprings is for my knife, I'm a bit over excited :D
-
-
A quick 84mm diversion. I finished this one up last night but forgot to post pics.
This is a red bantam, with brass liner and scissors. I've refined my technique on scissor grinding now to get a super snap out of the old 91mm backsprings. I added the video to show the the better snap action.
I guess I could call this an alox golfer too, but probably a full golfer needs the corkscrew and T&T.





Cheers!
-
Wow! Nice!

-
That's just lovely - wasn't there an 84mm model like that with ribbed Alox in the past?
I know I coveted them a lot but they were fetching silly money.
-
it only needs a corckscrew to be perfect, good job

-
As I know one of these backsprings is for my knife, I'm a bit over excited :D
Yours is going together right now with the shiny spring pictured. :D
All done! :D
The pictures were hard to take in my shop with florescent lights, but it's dark out now so this is the best I can do. ;)
Here is the new custom spring sitting with the scissors in open mode.

And here it is closed. Notice the scissor handle rests just right on that ramp I made. :D :D
:D :D
Here are a couple trying to show that it blends right in next to the stock Vic blade spring. Again, hard to tell from the photos but noone would know it was a custom spring and not stock unless they were told.


Chrissy I hope you like the mod, I think it turned out splendid! :D



And a quick video to show of the scissor action.
Alox 93mm SAK - Custom spring and scissors
Cheers!
-
Looking good, absolutely a thing of beauty! JR
-
Beautiful work as always. Can't wait to get a new knife to you.
-
Wooooo hoooooooooo, there she is :D
Been so worth the wait and awesome dealing with you on this. Can't wait to get my hands on it, and it's probably going to be my primary EDC for a great deal of the time. That backspring rocks

-
Looking great Syph, love the snap you are clearly getting.
Can the same spring be adapted for use on the 84mm frame? -
@Gareth said:
Looking great Syph, love the snap you are clearly getting.
Can the same spring be adapted for use on the 84mm frame?Sadly no. The 84 has more in common with the 91 as they share the center hole position (different size but some location). That's how I was able to use 91 springs on 84s to get scissors on. The 93s are completely their own beast as far as hole spacing for springs go. This spring I made up should work for a number of components though. I can even completely grind down the one end and use it for 2 tools.
If I run out of the old scissor backsprings from 91s that I got from Tom, I may have to make some springs up for the 84 scissor mods. I got a pile of them from him at the time, and I think i have 20 left, but he said he was running low on that old style last time I asked.
-
Tempting. I'm thinking about trying to scissor up a Cadet myself now that I found my old 84mm Climber.
-
@crackout said:
Tempting. I'm thinking about trying to scissor up a Cadet myself now that I found my old 84mm Climber.Hey if you already have 84mm scissors ready to go from a small climber, that mod should be straight forward. The nice thing about 84s is the parts between the alox size and cellidor are interchangeable, unlike the 91/93 sizes.
-
You mean like the pivot holes and liners? Yes, I like that, too.
However, I think I'd try to peen though. I'm not comfortable with drilling the 2.2mm holes to 3mm. Especially the center one. -
@crackout said:
You mean like the pivot holes and liners? Yes, I like that, too.
However, I think I'd try to peen though. I'm not comfortable with drilling the 2.2mm holes to 3mm. Especially the center one.Peening would be easier for sure. The funny thing is there is more metal on 84mm springs than 93mm springs. I drill 1/8 inch which is about 3.2 mm and there is far more metal left around the hole on 84s than 93s. It's just the way they were designed I guess.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login