PowerDuo poor quality--is it just mine?
-
@Scott86 said:
Dont know if you guys have seen this video yet, but it was enough to make me shy away from the powerduo.
https://www.youtube.com/watch?v=KX1O06mCbD8Would i ever use the can opener? I doubt it(Never have on my other MT's) but the fact that that was ignored by whoever green-lit the design tells me its probably got other issues as well.
Oh dear. :( I wonder if it has the same issue if you are trying to open a smaller can? Interestingly the placement of the can opener has dictated Victorinox design for years, if it is not the outermost tool it becomes hard (or impossible) to use. I believe this is also the reason we get the "left handed" liner lock on the 111mm line, the can placement of the can opener means a normal liner lock wouldn't work.
-
Dont know if you guys have seen this video yet, but it was enough to make me shy away from the powerduo.
https://www.youtube.com/watch?v=KX1O06mCbD8Would i ever use the can opener? I doubt it(Never have on my other MT's) but the fact that that was ignored by whoever green-lit the design tells me its probably got other issues as well.
Oh dear. :( I wonder if it has the same issue if you are trying to open a smaller can? Interestingly the placement of the can opener has dictated Victorinox design for years, if it is not the outermost tool it becomes hard (or impossible) to use. I believe this is also the reason we get the "left handed" liner lock on the 111mm line, the can placement of the can opener means a normal liner lock wouldn't work.
Yes absolutely. I made the mistake of trying the can opener on a non outer layer in a SAK and it has the same effect of being useless.
-
Oh wow, that's exactly the same spot where my scales are separated from the tool. That's quite a design flaw.
-
That is worse than mine but I am also dissapointed. The phillips on mine is not even useable. I paid less for the rebar than the powerduo so I was expecting a similair quality tool but they are no where near the same level of quality.
-
My powerDuo so far still work fine and n o big issues, but I still no try to open a can,
but the video worry me, I will check the can opener and see.. 
-
I got my SOG Powerduo too, with a minigrip.

Generally looked OK, apart from a crack on the covers, shown below. It appears that there was a pin sticking out which pushed the cover cracking it a bit. That **pin was not ** in at the other side!!
In the following picture you can see that that only the tip of the pin is in:
The blade opens nicely, though not as smoothly as in a SAK. Smaller than the SAK blade too.

The pliers are the standard, newer, pointier, smaller SOG pliers.


The gears used have more teeth but are thinner and smaller.

The extra tools are definitely not the ones used in standard SOGs. They feel and look cheaper.

They lock, but move a bit up and down (like other locking SOGs).
On mine, if you push them hard, in the direction in which they close (whilst locked) they will move worryingly up, shifting the liners with them. In mine this was caused by the pin not being in at the liner adjoining to the knife…. This pin also caused the cover’s crack, on the other side..**Seriously, ZERO for QC. **I loosened the covers and tried to set the pin in properly. However the pin will go in and then when released and the liners spread it will pop out again.
the picture below show the ptoblem.
I did not want to continue further than that. I fixed the covers back and decided that I have been had by SOG and considering that the shipping cost to them will be the same as the tool cost, will have to live with my mistake. My Gerber Dime had brilliant quality compared to that. At least I can fix it with a gentle tap from a hammer..
Generally good effort with the Pliers and the knife but the rest looks like a bad afterthought...The quality/execution of these tools is way below the quality of the blade and pliers sytems
-
Thanks for those pics comparing to normal SOGs. Its very obvious these are not made at the same factory as the other good SOGs, and are a cheaper made tool. I have zero interest in trying one for sure now. Thanks for saving me some $.

Those tools look pathetic to be honest, and SOG should be embarrassed to have their name on it. I love SOG stuff, so I hope this doesnt continue to other new tools they make or it's a real downer.
-
The blade looks and feels good in the hand (nice grip) and the pliers should be OK. However the rest I see as emergency use only.
-
I was kicking myself for not jumping on the group buy. Now I am happy that I didn't do it. I am so disappointed with SOG and wonder if this is going to be the standard of quality from SOG.
Sent from my Galaxy S3
-
-
this, along with the sogfari, I'm disappointed
-
I actually suspected this would be the case.
I think SOG has been forced to rush these out to satisfy consumer demands.However, that detailed picture showing the cogs on the new PowerDuo worries me immensly. The teeth seem more rounded off than previous SOGs but more worrying is that the left cog seems to be thicker gauge steel than the bottom right cog!! (or is it just the light playing tricks).
I too was all for buying one, but read a review posted on the HH site and withdrew my order. I can't/wont waste money on substandard workmanship especially when they're asking premium prices.
I do wonder how much damage the PowerDuo will have done to the next generation of Sogs built under license in China.
I'll now be very cautious and will scrutinize any new future releases from Sog.
-
Syph, what you see is just grease; prety normal.
Tosh, the sheet metal is prety thin. The cogs are the same thickness but finished at different "standards" so the tips are rounder on one of them (one set was filed more).
If Ganzo can produce a product with decent QC in China SOG should be able to do the same, too. It seems that they actually asked for the QC to be skipped. I remind people again: the powerduo IS NOT a low cost product!
Still like the pliers and the blade
-
You should all use the hell out of them, not at least that flimsy Phillips driver (and make tons of youtube vids) and then make SOG replace it.. >:)
-
So we agree that the knife and pliers are ok, while the rest of the tools are not. I think the solution is obvious. SOG should add a clip, remove everything but the pliers and knife, and voila! SOG Freestyle! :D
-
I still can't believe this is coming from the same company that made the Toolclip, PowerPlier, not to mention the Paladin 540..

-
I'm a "plier-kinda-guy", so I would never even have considered getting a SOGfari, but it seems things kinda went South when that Gunny character got involved, didn't it..

Gunny approved my _ _ _.... :P

-
I think it started when SOG was sold to that company, I guess bean counters had a field day and got us what we have now.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
Don't forget the SOGFari too.