And so it begins.... (My adventures into Alox!)
-
another lovely job.
-
I always wondered, why torx screws? I know a lot of knifemakers use it but wouldn't a phillips or flat head screwdriver be more easily serviceable? I mean you could tighten a SAK with a SAK :ahhh
-
@enki_ck said:
I always wondered, why torx screws? I know a lot of knifemakers use it but wouldn't a phillips or flat head screwdriver be more easily serviceable? I mean you could tighten a SAK with a SAK :ahhhI think both looks, and that you can get more torque on a torx. For a pattern of the same radius, you hve 6 points of contact vs 4. I like the look of the torx over philips too. Other than that the most plain answer is that, that is what all the knife supply stores sell... so thats what i use. :D
-
I always wondered, why torx screws? I know a lot of knifemakers use it but wouldn't a phillips or flat head screwdriver be more easily serviceable? I mean you could tighten a SAK with a SAK :ahhh
I think both looks, and that you can get more torque on a torx. For a pattern of the same radius, you hve 6 points of contact vs 4. I like the look of the torx over philips too. Other than that the most plain answer is that, **that is what all the knife supply stores sell... so thats what i use. ** :D
I thought it was something like that. :D
-
Today's project was a simple two layer. Pruner/blade with scissors. It's a nice little knife. :D




-
I always wondered, why torx screws? I know a lot of knifemakers use it but wouldn't a phillips or flat head screwdriver be more easily serviceable? I mean you could tighten a SAK with a SAK :ahhh
I think both looks, and that you can get more torque on a torx. For a pattern of the same radius, you hve 6 points of contact vs 4. I like the look of the torx over philips too. Other than that the most plain answer is that, **that is what all the knife supply stores sell... so thats what i use. ** :D
I thought it was something like that. :D
Be even better if they were titanium! JR
-
May Syph lead me not in to temptation....
Yeah, right ::)
-
The idea of putting the Philips opposite of the openers is truly genius.

Question, though, it looks as though there has to be a layer between them and the blade layer to access the bottle opener nail nick. Is this correct? If so, does it have to be scissors, or would a wood saw still allow access to the bottle opener nick.
I'm also curious, does not having the bottle opener up against the liner make it weaker? As in, it would take less prying force to make something break?
I've got the mod lust a-brewin'

-
@gustophersmob said:
The idea of putting the Philips opposite of the openers is truly genius.
Question, though, it looks as though there has to be a layer between them and the blade layer to access the bottle opener nail nick. Is this correct? If so, does it have to be scissors, or would a wood saw still allow access to the bottle opener nick.
I'm also curious, does not having the bottle opener up against the liner make it weaker? As in, it would take less prying force to make something break?
I've got the mod lust a-brewin'

No the nail nick sticks up high enough it shouldn't matter what the middle layer is, a saw should work fine.
I would think it would be stronger this way. The prying tool between a liner and a steel tool, instead of a liner and a soft aluminum scale. The steel pivots I use are stronger than brass as well.
-
Someone is trusting me to work on a marlin spike mod! :D


-
Ive done a few rivet jobs and they are ok, but I really like to be able to take knives apart to clean them proper, thats the biggest advantage for me. As far as screws backing out, no chance with red loctite. They dont move unless you want them too.
-
Here is the marlin spike mod all done up with brass liners and a scissors layer added. I still love brass every time I use it. I think it has a warm look and just a touch of color.
This is the first time I ever put an awl in place of the can opener, but the customer wanted the awl still. At first I thought it wasn't going to work as it hit the cap lifter, but I ended up bending the cap lifter the other way, so the opposite side is flat. Usually the normal flat side being flat up against the scale, but in the way of the awl. I didn't think it would bend nicely, but it did after all and it fits perfect. That was a pleasant surprise, as my first mod attempt was to shorten and regrind the awl, but it looked awful so I needed a plan B.
Cheers







-
Nice job, love it
JR -
Very nice and I love the brass with the green

-
beautifull color!! good work!

-
Marlin spike + awl :o that is some serious poking hardware :D :D :D.
Looks nice , I do like GREEN SAKs + the brass= 8) 8)

-
Stunning! Love the green color...

-
This thread has left me almost speechless, i tried to read most of it. Amazing stuff, well done!!!!!!!! I actually thought of the mod to use torx screws for modding alox last year as I had never seen anyone else try it and was not a fan of non factory peening. I hunted around for some tiny torx screws but it all got a bit too hard and then never did anymore on it. I don’t know where you find all your alox knives. Every site I go to says out of stock. Maybe you have been buying them all up LOL. I think I will can my idea of doing the mods my self and just get you to make me one. So hard to decided what to get though, but if I had to choose one, it would have to be HA red scales but I would like to provide my own from a soldier.
I have some questions
1 – how is the red HA holding up? Have you tried to mark it with something? I was always put off by red scales for EDC as I would be so paranoid about marking them and really get paranoid and have to baby it.
Would a 30cm drop onto concrete mark it? I am guessing other pocket tools would not mark the HA red either? Like others here, this is the FIRST time I have ever heard of hard anodizing in anything other than black/grey and olive military colour.2 – how are the custom back springs holding up long term? Are they as good as the vics? Not loosing tension at all?
3 – I cant really decide on brass or TI liners. Everything tells me to go TI for lighness but brass looks cool.
Whats the weight difference? I figure brass would be better as a natural bearing surface.4 – Can you please tell me how thick a 93mm alox would be with
Saw
Pliers
Scissors
Metal/wood file
Wood saw
Main blade/awl
Inline Phillips with can opener and cap lifter doubled up on the otherside. I like this idea best as it looked like the Phillips may have been hitting the scales in the closed position like you said.What is the best Phillips driver to use? I have already got 2 from 2 new old style explorers with the grey magnifiying glass. Is this the longer/better Phillips? Will it work opposite the can and cap openers or do I need the new style Phillips that goes opposite the modern all clear magnifying glass?
I think that’s all the tools, how ever I am also considering another layer possibly. Even if I don’t like the thickness I could always take the saw/file layers out maybe and have some spare shorter pins on hand too.
Because of the thickness/weight, would that need a stronger/thicker key ring tab? Would same thickness in TI be fine?
Another though, would it be possible to add the 91mm back spring phillips? i realise cutting the alox would be needed if its do-able.
Anyway I will have to start collecting the parts to send to you to do it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
