The Gohons aka Gerber Shears, Spring Loaded (pic heavy)
-
uhhh..
how did you know I got one of those in the mail? I literally have it sitting next my keyboard right now.
-
I just noticed that the video of the flick is screwed up:
-
Those shears re very nice, not to mention stealthy :D
-
Can anyone take a pic of the Freehand/Flik and a MP600?
I want to know if I can make a pair of Freehand Shears.
-
Sorry to necro this thread but I have some new ideas regarding this project.
After FINALLY getting a couple of pairs of leatherman OHTs I finally have a reason to mod something again.
Lets take a look:

You can see is that the OHT is a taller, perfect because the shears would sit proud unless you extend the channel like I did.

The channel is a lot thinner on the OHT. This means one of two thing. I have to either widen these channels or I have to thin out the sliding pivot. I would rather open up the channel.

Over all, the outside tools would be a winner combined with a set of shears.

The OHT is a fair bit roomier than the MP600 so adding an internal spring mechanism won't be that hard.

Just look at this! Over laying the tools, the head looks great!!

One more shot.
This calls for a rename, not sure what. Leatherman OHTS? One Hand Tactical Shear?
-
I like the idea of the LM OHT(S). I just do not have the know how to do something like this. Would you post your method pics of this mod (if you have them)?

-
@stealth007s said:
I like the idea of the LM OHT(S). I just do not have the know how to do something like this. Would you post your method pics of this mod (if you have them)?
The hardest part will be widening the channel so the sliding pivots can clear, the spring too. Other than those two operations, it wont be that hard.
I plan to set up my mill over the christmas break and i might able to do it then. Just keeping you guys up on the up :)
-
Looking forward to seeing the results mate.

-
Bah!
Tool apart the OHT, not as simple in construction as the MP600, it's nice to see.
In case you guys were wondering.

There needs to be spacers made for the mating surfaces. This may not work!
Since the mp600 is so much slimmer (would never think to say that), the shears aren't wide enough.

-
But that's a good thing isn't it, Eric?

It means you've got space to add in some Tufnol, Shamban or other slideway material to make the shears deploy even smoother than Gerber or LM pliers
(assuming you can get suitable screws that is
)I know it won't stump you for long mate ;)
-
@50ft-trad said:
But that's a good thing isn't it, Eric?
It means you've got space to add in some Tufnol, Shamban or other slideway material to make the shears deploy even smoother than Gerber or LM pliers
(assuming you can get suitable screws that is
)I know it won't stump you for long mate ;)
I have some nylon that would work, but I worry that there won't be enough weight to shoot them out.
Your right, I put aside to work on the Commander :)
-
@50ft-trad said:
But that's a good thing isn't it, Eric?

It means you've got space to add in some Tufnol, Shamban or other slideway material to make the shears deploy even smoother than Gerber or LM pliers
(assuming you can get suitable screws that is
)I know it won't stump you for long mate ;)
I have some nylon that would work, but I worry that there won't be enough weight to shoot them out.
Your right, I put aside to work on the Commander :)
Hmmm ... I'm wondering if nylon might be a bit too grippy
Even if not, it might deform and jam up the deployment if you try to cut heavy materials (I've used it for fashioning thread locking devices before the same way) -
@50ft-trad said:
@50ft-trad said:
But that's a good thing isn't it, Eric?

It means you've got space to add in some Tufnol, Shamban or other slideway material to make the shears deploy even smoother than Gerber or LM pliers
(assuming you can get suitable screws that is
)I know it won't stump you for long mate ;)
I have some nylon that would work, but I worry that there won't be enough weight to shoot them out.
Your right, I put aside to work on the Commander :)
Hmmm ... I'm wondering if nylon might be a bit too grippy
Even if not, it might deform and jam up the deployment if you try to cut heavy materials (I've used it for fashioning thread locking devices before the same way)Yah. Maybe aluminum. I don't know.
-
What kind of stuff can those shears cut through?
Can they work as hard wire cutters?
-
Amazing project, I like the way you push boundaries.
Could there be shear based MTs which can cut through coins?
-
Amazing project, I like the way you push boundaries.
Could there be shear based MTs which can cut through coins?

Why?

That was my thoughts too
-
Just because! Making the impossible work, right? I need to get my multi modding hat on
:D -
@tattoosteve99 said:
Just because! Making the impossible work, right? I need to get my multi modding hat on
:DShort of designing my own shears and dropping them in...maybe I can design them and then 3d print them.
Won't be functional but they can be tested for fit :)
I really want a butter fly style one.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login