My Leatherman post #2
-
Oh no, not good!¡! Did you hit the LM with the hammer?

-
@stealth007s said:
Oh no, not good!¡! Did you hit the LM with the hammer?
No, I was holding the ringed nails so they don't bend while driving them. I suspect lateral forces from the nail, (when hit) finally broke the jaw.
-
One question, is it cold where you are? Other than lateral force the cold may have played into this?

-
Oh dear :(
-
@stealth007s said:
One question, is it cold where you are? Other than lateral force the cold may have played into this?Not really. I attribute it to fatigue. These are cast pliers heads not forged, so not as strong as a standard set of pliers
-
MAN DOWN, MAN DOWN !!!
-
So are you going it to send it in to LM for repair/replacement? -
Bummer Nate! At least he went down like a man.
-
:ahhh
This is like a horror movie for MTs. That sucks. Hope you get the replacement soon.
-
I'm sorry to see this. That one was your favorite, right?
-
Time for Rebar mod!!!

-
Agreed. Even if you didn't belt it with a hammer it would still likely have been subject to shock loading and castings don't tend to like that, their grain sturcture just isn't up to it (they're not as bad in compression, but poor with bending/tensile/torsional forces). Forged heads would be altogether a different matter, but we'd all be paying a massive premium on our multitools if that was the case. Also, I personally wouldn't feel comfortable sending it in as I would feel that I was at fault rather than the tool ... but your views may differ of course

-
A question: Are victorinox plier's heads cast or forged??
(Forging could also be done with a machine, by the way, not with a blacksmith using an anvil) -
@50ft-trad said:
Agreed. Even if you didn't belt it with a hammer it would still likely have been subject to shock loading and castings don't tend to like that, their grain sturcture just isn't up to it (they're not as bad in compression, but poor with bending/tensile/torsional forces). Forged heads would be altogether a different matter, but we'd all be paying a massive premium on our multitools if that was the case. Also, I personally wouldn't feel comfortable sending it in as I would feel that I was at fault rather than the tool ... but your views may differ of course
I will be sending this in. To me, if you market something as a pair of pliers, it should function like a pair of pliers. Holding a nail (or screw) as you drive it to keep it straight is a pretty standard function of a pair of pliers. If I were using the pliers as a drift, or prybar, I'd agree with you. However, grabbing and holding something firmly is well within the description of what one does with a pair of pliers.
BTW, to finish the job, my wife tossed up and old pair of cheapo cast pliers I've owned for 30 years. No problem with those. ;)
I think the thinness of the jaws at that point really concentrates the forces there. I am likely the unusual case in that I use my Charge nearly every day in a hard use capacity. Numerous cycles of loading and unloading tends to form microcracks in cast parts, which lead to sudden failures like this.
-
That stinks, I think the tears would have been flowing !
-
Maybe it was just their time to go?¿?

-
@dks said:
A question: Are victorinox plier's heads cast or forged??
(Forging could also be done with a machine, by the way, not with a blacksmith using an anvil)Damn good question

@Mr. Whippy said:
@50ft-trad said:
Agreed. Even if you didn't belt it with a hammer it would still likely have been subject to shock loading and castings don't tend to like that, their grain sturcture just isn't up to it (they're not as bad in compression, but poor with bending/tensile/torsional forces). Forged heads would be altogether a different matter, but we'd all be paying a massive premium on our multitools if that was the case. Also, I personally wouldn't feel comfortable sending it in as I would feel that I was at fault rather than the tool ... but your views may differ of course

I will be sending this in. To me, if you market something as a pair of pliers, it should function like a pair of pliers. Holding a nail (or screw) as you drive it to keep it straight is a pretty standard function of a pair of pliers. If I were using the pliers as a drift, or prybar, I'd agree with you. However, grabbing and holding something firmly is well within the description of what one does with a pair of pliers.
BTW, to finish the job, my wife tossed up and old pair of cheapo cast pliers I've owned for 30 years. No problem with those. ;)
I think the thinness of the jaws at that point really concentrates the forces there. I am likely the unusual case in that I use my Charge nearly every day in a hard use capacity. Numerous cycles of loading and unloading tends to form microcracks in cast parts, which lead to sudden failures like this.
Fair play to you mate
If you feel that you used them in a way you think they should perform comfortably, then yeah they should go in :)As an aside, stress cracking / fatigue generally tends to look different if that's the case, you tend to have a smooth shiny (almost like rippled or volcanic glass) part to the fracture where the crack has been opening and closing against itself and extending into the parent metal, then a more crystalline part where the actual final break occurred. If it's a crystalline break throughout, it's generally a more acute failure in my experience, even on castings. Occasionally a crystalline appearance with colour variations across the break can indicate something taking a little longer to develop.
Anyhow .... My views of not sending it in are purely based on my own expectations from a given tool, not a reflection of your use
Maybe I feel that way with this partly because I know if I did that, I probably would have brayed them repeatedly with a hammer 
-
@50ft-trad said:
A question: Are victorinox plier's heads cast or forged??
(Forging could also be done with a machine, by the way, not with a blacksmith using an anvil)Neither would be my guess, for sure not cast. I would guess they are stamped out of sheet stainless like every other part they make, then riveted together.
-
If the sheet is pressed with rollers can they be considered "forged", at least strength wise? (like Sandvic mora steel)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


