Affordable Easy Sharpening System
-
I use a Lansky at home. It took a bit of practice to get used to it, but now I can get a blade shaving sharp very easily.
At work I keep one of the small Smith's pocket sharpeners or the Lansky version of it in my locker for quick touch ups. Whatever system you get, make sure that you play around with it a bit with a beater blade until you're comfortable with it. -
+1 for the Sharpmaker

-
I use the Sharpmaker . I am however competent with freehand , just that having a set up Sharp Maker is just so handy . I'm not fond of the Lansky , I have one , but it's gathering dust .
I have a DMT folding med/fine diamond stone in my tool box , and have strops all over the place .
I used to own an Edge Pro , just found it too time consuming . And they are rather spendy !
Chris
-
I recently got the Work Sharp "Guided Field Sharpener" and I have to say it has done a great jog at getting a nice sharp edge every time I have used it.
http://www.worksharptools.com/manual-sharpeners/guided-field-sharpener/flypage.pbv.tabs.tpl.html
-
I have to admit that I was too lazy to read all the responses, but I can tell you that I have the Spyderco sharpmaker, a lansky turnbox, a smiths pocket stone, a smiths double sided diamond stone, and several coarse/fine tool sharpening stones along with a ten or so cheap "V" shaped keychain sharpeners that are only good for the occasional kitchen knife.
The best for the money in my mind is the Lansky turnbox. It's about $11 and if your knife is plain edged then it will serve you well and there are additional sticks you can buy with various levels of abrasion. If you have a serrated blade, the Spydie sharpmaker is your best bet, and also has expansion sticks. With careful sharpening that system is tops, but it will set you back nearly $80.
-
I do use the Smith's Pocket Sharpener for the tapered diamond file on my Leatherman Charge TTi's Cut Hook. Followed by the Lansky Pocket Crock Stick's ceramic stone to put a fine cutting edge on.
Was dinking around this evening and noticed that after cutting a guide through the plastic wall, following the angle given by the inner rod holder, was able to extend the ceramic stick through to the outer side.

Pressing down on the inside > gives a decent angle to drag the cut hook horizontally. Then on the other side. Am happily to say it gives a nice clean paper cutting edge. :)


-
I was the same as OP; thought freehand sharpening was an arcane skill that I didn't have the time to learn. Bought a spyderco sharpmaker, which is great for taking a dull edge to super sharp, but without the diamond stones it's a lot of effort for completely blunt knives, so I bought the Fallkniven DC4 as well; the diamond side really eats metal and lets you turn something with no edge at all into a blade.
Between those two, I'm completely happy.
-
@Yak-er said:
I have a setup that looks exactly like the Spyderco but it is made by Cutco. I used to sale/service Cutco and it was part of the service kit. It works great for blades that just need touched up. If there is a nick or ding it takes forever to take it out on that setup. I need something that can be more aggressive. Anyone ever used the Lansky system? http://lansky.com/index.php/products/dlx-5-stone-system/How about the Edge Pro Apex, very spendy but highly recommended on YouTube. http://www.edgeproinc.com/Apex-Model-Edge-Pro-System-c3/ I have a feeling this really works but its really more than I want to spend.
By the way the other suggestions seem to be easy but lack the capability I need/want.
I have the Lansky in the link above, and I like it. I fully echo Jamie_M, sparky415 and jerseydevil's comments on it.
-
I am pretty convinced that I'll buy a Lansky. With it plus my Cutco Ed Reed sharpener (same idea as sharpmaker) and a whole box of wet stones I should be able to put decent edges on about everything or total screw them up :D.
-
Work sharp guided belt system. 110% awesome. All I use any more.
The Ash Mobile Voom Voom
-
If you know how to freehand , or are committed to learning , a Spyderco Doublestuff , a leather strop of the same size + a leather bootlace loaded with abrasive will do pretty much all . ( the abrasive loaded bootlace being for serrateds ) . Just get your practice in on lower end Vic. or Henkel paring knives ( cast plastic handles ) .
Chris
-
I went with the lansky system after asking advice in here. It's very simple to use and there's plenty of vids on YouTube if in doubt. I'd recommend it
-
It's $150 but trust me, it's more than worth it: The Chef's Choice 120. It really works, and it's easy. Just follow the directions exactly and you'll get a really sharp edge.


-
I dont know about you Yak-er, but due to reading this thread I've just ordered the Lansky Turnbox four
cant wait to get it and give it a try -
Trying to correct something... ;)
Do use the Smith's Pocket Sharpener for the tapered diamond file on my Leatherman Charge TTi's *Cut Hook*. Followed by the Lansky Pocket Crock Stick's ceramic stone to put a fine cutting edge on. Was dinking around this evening and noticed that after cutting a guide through the plastic wall, following the angle given by the inner rod holder, was able to extend the ceramic stick through to the outer side. From...
To...
Pressing down on the inside > gives a decent angle to drag the cut hook horizontally. Then on the other side. Am happily to say it gives a nice clean paper cutting edge. :)


Will have to try this on the Tread to see if it sharpens it okay. *Makes ones wonder, how does Leatherman sharpen these cutting hooks in the first place?*
-
I think that going back to edit a 3 & 1/2 year old post to correct something should qualify you for the OCD badge.

-
@PTRSAK said:
I think that going back to edit a 3 & 1/2 year old post to correct something should qualify you for the OCD badge.
Nah, I have been referring people back to this page for my sharpening methods. It's embarrassing to see all the old photos gone. Since I don't have moderator powers I figured it was best to update it. And with MTO, I can past the link to the updated posting. :D -
I have to say that the Sharp maker is probably the best option, at least in my mind. The others also have serious benefits for sure, but when it comes to fast and easy results with little to no effort to learn or set up, the Sharp maker is pretty well impossible to beat.
Def
-
@thesuper said:
I dont know about you Yak-er, but due to reading this thread I've just ordered the Lansky Turnbox four
cant wait to get it and give it a tryYou won't be disappointed. I got one for Christmas and love it. If all you're doing is fine edge blades it works great. And I'm experimenting to see if it works on serrated blade of my wave.
-
@Xelkos said:
I think that going back to edit a 3 & 1/2 year old post to correct something should qualify you for the OCD badge.

Nah, I have been referring people back to this page for my sharpening methods. It's embarrassing to see all the old photos gone. Since I don't have moderator powers I figured it was best to update it. And with MTO, I can past the link to the updated posting. :DWay back when I first joined you had an unlimited amount of time to edit and reedit posts but it got to the point they were afraid somebody would go back and delete some some good bit of knowledge after getting mad so they put the limit on the editing

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login