Broken Wave?
-
Was it like that when new or did it go loose after you cut a screw? Some metals,(like SS nails) can be very hard.
Really, the dealer is your best bet. Obviously it is, now, damaged.
-
Here's what I was cutting. I got even more play when I rolled this thin stuff up into a smaller piece. Like said, Christmas day, it couldn't cut some stranded wire with a small piece of metal smooshed around it. It bent like now. Also, I later tried moderately hard to cut a penny, but didn't try my hardest by any stretch of the imagination. Should small metal things be able to bend the massive pivot on a Wave or is it play that is not seen until pressure is exerted?

-
Definitely more play than originally. There was none new. Do Waves develop play over time? (under a week?)
-
No.
See the seller/dealer for a repair.
-
Ok, I'll be returning it. LLBean does free shipping both ways and a brand new product guaranteed in such cases so it's just a time issue. I still have my old Sheffield wooden handled multi for now. When I get a new one, what is the maximum size for something the regular wire-cutters can cut? Should thin stranded wire (or anything else not a clean cut) be able to bend the huge pivot?
-
It sure sounds like this tool was defective as it should take a huge amount of force to displace the jaws like that on a new tool.
While usually favored over other thypes I do think bypass cutters are more likely to have this type if issue (if defective) though as anything that wedges between the blade now exerts a sideways force, wedging the pivots 90 degrees from the designed loading. It should not have happened anyway but if there was a workmanship issue this could do it.
Anvil cutters, while having their limitation do not force the jaws sideways, they either won't cut, won't close or will nick and deform but at least the load stays applied in the direction the pliers pivot, not 90 degrees to it.
Tony
-
@Heirphoto said:
It sure sounds like this tool was defective as it should take a huge amount of force to displace the jaws like that on a new tool.While usually favored over other thypes I do think bypass cutters are more likely to have this type if issue (if defective) though as anything that wedges between the blade now exerts a sideways force, wedging the pivots 90 degrees from the designed loading. It should not have happened anyway but if there was a workmanship issue this could do it.
Anvil cutters, while having their limitation do not force the jaws sideways, they either won't cut, won't close or will nick and deform but at least the load stays applied in the direction the pliers pivot, not 90 degrees to it.
Tony
Well put. So, does this mean that anything not cut (stranded wire, etc.) will force the jaws apart the wrong way? Because that sounds like a terrible thing to implement in a tool. In a non-defective tool, what do you think should happen when strong force is used on stranded wire (and the like)? Does one need to take precaution not to cut certain things?
-
It looks like you have damaged your **wire ** cutters mate, I think you are actually abusing the wire cutters by cutting pennys, screws & bullet casing. I think a lot of multi tools would be damaged by that abuse
. I think LM could easily say the warranty is null & void as what your doing is not what the tool was designed for , like I said they are 'wire cutters' not cut everything cutters.The bur you created will effect the pliers function + I think the abuse has caused the pliers to become deformed/distorted hence they are not lining up.Most(not all) modern Leatherman have a round cut out at the base of wire cutters designed for hard wire, your Wave has this(there are 2 arrows pointing too it) & they can cut nails if put into the hard wire notch but even then I would be super careful as you could damage the tool doing that.
-
Thank-you mate for the honest truth. I guess I expected to much of my tool. So, are the wirecutters only useful for cutting thin, non-stranded, flexible (not hard), wire (probably wrapped in rubber-plastic)? Would I be able to do a lot more with the Rebar head?
-
The standard cutters are for soft wire (copper, aluminum, etc) braided or solid strand. The hard wire cutters are for hard wire (steel mostly). The cutters in most mulititools are not nearly as durable as dedicated cutters. I try to avoid steel wire in my cutters unless that's all I've got. Screws are very hard, I would never try to cut them with any cutters, especially a multitool. An abrasive wheel is the best way to cut a screw, or just use the pliers to break it off.
-
Here's my old multi. I have alot to learn about proper usage or wirecutters.
-
As you realised, if you cut a lot of hard or thick materials then dedicated cutters will be the answer.
In addition to the potential for damage multitool handles tend to flex and twist when you are cranking down and twisting/turning to cut a thick/hard piece of metal and could loosen up. Dedicated cutters with solid handles will not have any such problem and they are usually cheaper than a good multitool.
I do on occation cut cables, a few mm thick with my ST300, out of laziness, but I always know and feel that the tool is not happy doing that. Note the ST300 has *replaceable cutters * if I really damage the tool and speSmurfpillsed *Stranded-wire Cutters * that are better in some situations. -
@scorpion008 said:
Thank-you mate for the honest truth. I guess I expected to much of my tool. So, are the wirecutters only useful for cutting thin, non-stranded, flexible (not hard), wire (probably wrapped in rubber-plastic)? Would I be able to do a lot more with the Rebar head?No worries mate , from the look of your photo you have really trashed your Wave's wire cutters :o, I would be surprised if it got replaced under warranty

Like dks said maybe a LM model with replaceable wire cutters would be better for you like the Rebar or SuperTool 300(hopefully LM will add these too more models) BUT even then cutting what you did with your Wave, with LMs new style cutters would not only damage the cutters(not a big problem as they are replaceable} but cause twisting/bending of the pliers to the point were the pliers do not line up, ruining your pliers.
If you use LMs hard wire cutting notch you can cut most wire & some people have been able to cut stranded wire with them, the SuperTool 300 does have a dedicated stranded wire cutter.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login