Which FOLDING KNIFE did you carry today?
-
Opie #5 today
bottom one,
-
@Northern Geek said:
That's a really beautiful edge..
Wish I had the equipment, skill and patience to do that to my own knives.. :P
+1 on the beautiful edge.
As for patience when sharpening knives, I actually find freehand knife sharpening quite relaxing.
-
@stealth007s said:
Forgot to post a pic
Sent from Endor using Schlapatok
Terry that's a pre 2000 opie as looks like no notch for locking it closed

-
@Northern Geek said:
That's a really beautiful edge..

Wish I had the equipment, skill and patience to do that to my own knives.. :P
+1 on the beautiful edge.
As for patience when sharpening knives, I actually find freehand knife sharpening quite relaxing.
Well let me rephrase that then.. I wish I had the equipment and the skill.. :D
-
@Zed said:
Terry that's a pre 2000 opie as looks like no notch for locking it closed
Thanks Paul

@prime77 said:
I use pretty much the same system now a days for the harder steel knives. To re-profile a factory edge I use DMT continuous plates at Coarse, Fine, then Extra Fine. Then a quick polish with Spyerco double stuff medium and fine. Then a final polish on a Spyderco ultra fine stone. Followed by some stropping with diamond paste. Here are some of the stones and strops I use.
Of course all this is just to re-profile an edge. Touch up after use can be done with just a strop or Spyderco UF stone to bring back that hair whittling edge.
Here is a close up of the 0551 edge.


I had a guy that would sharpen knives for me years ago at the Ft Stewart PX in a kiosk. He used a wheel to sharpen and a buffing wheel with a compound on it to shine the edge like that. I am wanting to learn his technique but I'm needing the motor and wheels

-
Razor Sharp is the system you are describing. http://www.sharpeningwheels.com/
I have these wheels mounted on a variable speed buffer, which looks like a bench grinder but the motor is thinner and the wheels are farther apart. With a little practise, I can now sharpen most anything, and quickly! Except ceramic blades, as it overheats the wheel.
There is a massive thread over at blade forums all about paper wheels.
Dave
Sent from my iPad2
-
Thanks for that Dave
Ceramic need sharpening?¿? 
I really need to join BF

-
@stealth007s said:
Thanks for that Dave
Ceramic need sharpening?¿? 
**
I really need to join BF**
bad Stealth, bad! 
:D :D
Back to carrying my Byrd Tern again today. Recently I really have only been carrying a SAK or the Tern as my pocket knife, I do need to dig out some of my other blades. :-[
-
Carried a Buck nini toothpick and an Opinel 8. Used them to push-cut paper to see if they were sharp...

-
I've been on a ultra light kick of late, carrying only the most compact of tools. My carry knives have been either an A.G. Russell ultra penknife, a Vic classic, a Case peanut, or a Buck 309 companion.
-
Hey Prime what do you sharpen your knives with? They all have that mirror edge :o
I use pretty much the same system now a days for the harder steel knives. To re-profile a factory edge I use DMT continuous plates at Coarse, Fine, then Extra Fine. Then a quick polish with Spyerco double stuff medium and fine. Then a final polish on a Spyderco ultra fine stone. Followed by some stropping with diamond paste. Here are some of the stones and strops I use.

Of course all this is just to re-profile an edge. Touch up after use can be done with just a strop or Spyderco UF stone to bring back that hair whittling edge.
Here is a close up of the 0551 edge.


Thanks for the response bro

-
Prime, can you give a ballpark figure as to how much is would cost to acquire a kit like that?
My sharpening skills are adequate, but I really want to perfect them so that my blades are all as perfect as they can be. I tend to only be able to bring a knife back to 90% of it's sharpness. They work just fine, but they aren't as sharp as they should be.
-
@Mercury said:
Prime, can you give a ballpark figure as to how much is would cost to acquire a kit like that?My sharpening skills are adequate, but I really want to perfect them so that my blades are all as perfect as they can be. I tend to only be able to bring a knife back to 90% of it's sharpness. They work just fine, but they aren't as sharp as they should be.
I did some quick adding up of the stuff and got the following. I went with three 6 X 2 DMT Continuous stones because the larger ones are pretty expensive at around $90.00 a piece. Some people like larger stones but I learned to freehand on smaller stones so I don't have a problem with the 6 X 2. Each 6 X 2 is $26.95. I think they are a great deal. They will last a lifetime, don't need flattening and cut harder steels really well. That's $80.85 for the three DMT stones. The Spyderco double stuff was $27.95 and is a great pocket stone that is great for touch ups and for polishing an edge coming off the three DMT stones. The most expensive stone will be the Spyderco UltraFine stones at $82.95. But it is SO! worth the money. I can't say enough praise about the UF Spyderco stone. A great finishing stone that leaves you with an amazing edge. And this is the only touch up stone you will ever need. Lastly I made the three strops myself but I got the leather at a local belt makers shop for like $15 bucks for a scrap piece. The diamond pastes come in a three pack from DMT and were $24.95 but they will last forever as you don't need that much on each strop to get the job done. All in all the grand total for the system was $236.70. It seems like a lot but I got mine overtime. You can skip the Spyderco UF stone and still get a really sharp my edge but like I said I love mine and don't regret the purchase at all. Good luck putting your system together. It can be allot of fun.
Sorry if this was Off Topic to some so in the spirit of the thread this is what I carried today.
My home stonewashed Spyderco Endura

-
So, I guess you use the diamond paste last on the strop?

-
I find the work sharp sharpener is a great system and if you buy extra belts you can get up to a 12000 grit and it puts a super nice polish. I then strop with bark river green and white compound and it produces a mirror edge. I absolutely love this system. Cost around 100-150 for everything. That includes sharper system from amazon, extra belts from another company, strop and compound from ksf.
A strop will save steel and refine and edge greatly. It also puts a superb polish on it.
Ash's mobile on the move.
-
@stealth007s said:
So, I guess you use the diamond paste last on the strop?
Yes Sir.
-
Spyderco Delica and BM 2550 automatic. :D
-
A guy at a local knife store told me that the Gerber Remix, and all other ring-knives were illegal in Canada. The Gerber Remix is sold openly in most of the large stores here. I think he may have been confused by the wording of the law that prohibits "finger rings with blades attached." I don't think either the Gerber Remix or the * CRKT Hole in One* is a finger ring of any kind.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

