What Did You Use Your Multitool For Today?
-
I used my SAK Pioneer to open a couple of packages that arrived today. One contained another Juice and one had a Minichamp in it. :)
-
Used the knife on my Juice S2 to cut my ribeye at lunch today
I was going to pull out the Opie No8 but I thought I'd better not as it may scare people
I usually use the S&W HRTF to cut my meat with but I wanted to put the S2 through some task as it's new to me. Worked very well!¡! 
-
My Pirahna likes bottle caps.
-
I used my Juice S2 small screwdriver to poke holes in the drywall and install screws so I could rehang a picture and mount a tip preventer on a new (to me) hall tree that I got today from a friend of mine from the cigar club
I used the MUT hammer to install the anchors for all the above. I'm having trouble with the image attachment thing so I'll post them from Tapatalk later 
-
@sir_mike said:
I used my SAK Pioneer to open a couple of packages that arrived today. One contained another Juice and one had a Minichamp in it. :)Does that make your Pioneer a sort-of "meta-tool" ?
for the curious: http://en.wikipedia.org/wiki/Meta
-
I used my SAK Pioneer to open a couple of packages that arrived today. One contained another Juice and one had a Minichamp in it. :)
Does that make your Pioneer a sort-of "meta-tool" ?
for the curious: http://en.wikipedia.org/wiki/Meta
Heck yeah! :)
-
Used the file on the Juice to smooth off some rough edges on the scale of a Victorinox Huntsman which I got yesterday.
-
I used my Rebar to remove a screw to check on a part of a new (but old) toy I purchased recently. >:D
-
I used my wave to open the package on wave's new big brother, my recently purchased surge!
-
I turned into Mr Handyman last night with all the picture hanging and wall mount stuffs. I'm not at all a handyman
I also fixed the raised rack on the grill that lost a nut. Used the S2 again for that. Here's images from last night's escapades.Sent from Endor using Schlapatok




-
I tested out the cap lifter on the Wenger Evo S17 last night. I think it works better than the cap lifter on Vics.
I also used the scissors on it to cut open a plastic bag... worked great.
-
Installed a handle on the top of a spaceheater today. I tried using the awl to start the holes, but ended up drilling them instead. I drove the Phillips wood screws into the plastic body with the Juice, and had no problems at all.
-
TTi to squeeze, bend, chop and file a can key in to a trolley opening key.
Everything I needed in one tool

-
I used my leatherman style ps to fix a static shock reboot problem on my gaming pc.
-
I was carrying my Gerber Balance all weekend. Just used the scissors to trim a split thumbnail, and the knife to open a package and a new duvet - decided to get a 13.5tog on there instead of the lightweight one instead of the lighter one that's seen me through the winter so far. It was toastie last night :)
-
Used the tip of the Charge AL plain blade to carve a dome lamp socket that had melted a little out of shape. A bit of fine detail work, but the clip-point came through.

-
Used both my Skeletool and Charge to fasten the bolt that holds the showerhead in the right position.
-
Tested my new PST II's can opener. Didn't do too bad. Then tried my Vic Explorer's can opener and it did fairly well. It definitely outperformed the Leatherman can opener. I didn't test that against the modern Leatherman can opener though, just the PST, which I don't think is quite as sharp as the newer ones.
-
@Monrogue said:
Tested my new PST II's can opener. Didn't do too bad. Then tried my Vic Explorer's can opener and it did fairly well. It definitely outperformed the Leatherman can opener. I didn't test that against the modern Leatherman can opener though, just the PST, which I don't think is quite as sharp as the newer ones.One thing to keep in mind about Leatherman's can openers is that they are also marketed as bottle openers. So they can't be too sharp, or too well-shaped for either one. They'll get the job done, but won't leave you awe-struck either.
A bit of practice with a Victorinox can opener will have you wondering if a dedicated one is really any faster. (I'm sure Lynn knows, hehehe)
-
I'd like to see a comparison of multi tool can openers. Maybe a can opener race.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login